Maytag MET3800TW2, Инструкция пользователя

Страница: 9 / 40

9
TROUBLESHOOTING WASHER
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call...
In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca
Washer and Components
Noisy, vibrating, off-balance
■ Is the floor flexing, sagging, or not level? Flooring that flexes or
is uneven can contribute to noise and vibration of the washer. A
¾" (19 mm) piece of plywood under the washer will reduce the
sounds. See the Installation Instructions.
■ Is the washer/dryer level? The washer/dryer must be level. See
the Installation Instructions.
■
Is the load balanced? Evenly distribute the load in the washer
basket and make sure the height of the load does not exceed the
top row of basket holes.
■ Did you completely remove the yellow shipping strap with
cotter pins? See the Installation Instructions.
■ Are the gears engaging after the drain and before spin, or is the
upper part of agitator clicking during wash?
These are normal
washer noises.
■ Is the washer gurgling or humming? When the washer drains,
the pump will make a continuous humming with periodic
gurgling or surging sounds as the final amounts of water are
removed. This is normal.
■ The washer basket moves while washing. This is normal.
Leaking
■ Are the fill hoses tight?
■
Are the fill hose gaskets properly seated? Check both ends of
each hose. See the Installation Instructions.
■ Is the drain hose properly installed? The drain hose should be
secured to the drainpipe or laundry tub. See the Installation
Instructions.
■ Is the sink or drain clogged? Sink and drainpipe must be able to
carry away 17 gal. (64 L) of water per minute. If sink or drainpipe
is clogged or slow, water can back up out of drainpipe or sink.
Check household plumbing (laundry tubs, faucets, drainpipe,
water pipes) for leaks.
■ Is water splashing off the tub ring? Center the tub before starting
the washer.
■ Is water splashing off the load? Evenly distribute the load in the
washer basket and make sure the height of the load does not
exceed the top row of basket holes. The fill or spray rinses can
splash off the load.
Dispenser clogged (on some models)
■ Did you follow the manufacturer’s directions when adding
fabric softener to the dispenser (on some models)? Measure
fabric softener and slowly pour into the dispenser. Wipe up all
spills. Dilute fabric softener in the fabric softener dispenser.
Washer Operation
Washer won’t run, fill, rinse, or agitate; washer stops
Electrical S hock Hazard
Plu g into a g rounded 3 pron g outlet.
Do not remove g round pron g .
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
■ Is the power cord plugged into a grounded 3 prong outlet? Plug
power cord into a grounded 3 prong outlet.
■ Are you using an extension cord? Do not use an extension cord.
■ Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
■ Are the water inlet valve screens clogged? Turn off the water
and remove inlet hoses from the washer. Remove any
accumulated film or particles. Reinstall hoses, turn on water, and
check for leaks.
■ Are both the hot and cold water faucets turned on? Turn on the
water.
■ Is the water inlet hose kinked? Straighten the hoses.
■
Does the water level seem too low, or does the washer appear
to not fill completely?
The top of the agitator is much higher
than the highest water level. This is normal and necessary for
clothes to move freely.
■ Has a household fuse blown, or has a circuit breaker tripped?
Replace the fuse, or reset the circuit breaker. If the problem
continues, call an electrician.
■ Is the washer in a normal pause in the cycle? The washer pauses
for about 2 minutes during certain cycles. Allow the cycle to
continue. Some cycles feature periods of agitation and soak.
■ Is the washer overloaded? Wash smaller loads.
■
Is the lid open? The lid must be closed during operation. Washer
will not agitate or spin with the lid open.