Maytag MER6875BA Series Скачать руководство пользователя страница 3

Страница: 3 / 11

Component Testing Procedures

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.

July 2006

16027361

Illustration Component

Test

Procedure

Results

Bake element, upper

Disconnect wire leads to element and
measure resistance of terminals...............

Measure voltage at bake element.............

Approximately 31.0

Ω

240 VAC, see wiring diagram for terminal
identification. If voltage is not present at
bake element, check wiring.

Bake element, lower

Disconnect wire leads to element and
measure resistance of terminals...............

Measure voltage at bake element.............

Approximately 21.3

Ω

240 VAC, see wiring diagram for terminal
identification. If voltage is not present at
bake element, check wiring.

Broil element, upper

Disconnect wire leads to element and
measure resistance of terminals..............

Measure voltage at broil element.............

Approximately 25.4

Ω

. If not, replace.

240 VAC, see wiring diagram for terminal
identification. If voltage is not present at
broil element, check wiring.

Broil element, lower

Disconnect wire leads to element and
measure resistance of terminals...............

Measure voltage at broil element..............

Approximately 18.6

Ω

240 VAC, see wiring diagram for terminal
identification. If voltage is not present at
broil element, check wiring.

Indicator lights

Measure voltage at indicator light ............. If voltage is present and light does not

work, replace light.
If voltage is not present at indicator light,
check wiring.

Rocker switch

Measure continuity of switch positions:

Open.....................................................
Closed ..................................................

Infinite.
Continuity.

Door plunger switch

Measure continuity at the following
points:

C-NO ....................................................

Plunger in:

......................Continuity.

Plunger out:

....................Infinite.

Limiter Normally

closed.

Verify proper operation.

Open....... Approx. 216° F (102° C) ......
Closed..... Approx. 176° F (80° C).........

Infinite.
Continuity.

Autolatch assembly
with switch

Disconnect wires and test for continuity
per wiring diagram....................................

Refer to Parts Manual for correct
autolatch switch associated with the
correct manufacturing number.

See wiring diagram for schematic layout.
Access assembly by removing left side
panel.

Temperature sensor

Measure resistances ................................ Approximately 1000

Ω

at room

temperature (75° F).

Convection element

Disconnect wiring to element and
measure cold resistance of terminals .......
Measure voltage at convect element ........

Approximately 30

Ω

240 VAC.

Convection motor,
2-speed

Measure voltage.......................................
Remove wires, check resistance..............
Check motor windings to ground ..............

Motor, hi-speed.....................................
Motor, low-speed ..................................

120 VAC.
Approximately 30

Ω

No continuity.
Approximately 1200 RPM.
Approximately 900 RPM.

Содержание MER6875BA Series












Результаты поиска

Содержание MER6875BA Series

Отзывы:

Бренды по названию

Популярные бренды

Maytag MER6875BA Series, Техническая информация

Результаты поиска

Содержание MER6875BA Series

Отзывы:

Бренды по названию

Популярные бренды