manualshive.com logo in svg

Maytag MDG75V, Руководство по установке, Страница: 33 / 51

Поделиться
Скачать
Maytag MDG75V Скачать руководство пользователя страница 33

29

H.  PREPARATION FOR OPERATION/START-UP

The following items 

should be

 checked before attempting to operate the dryer:

1. Read 

ALL

 “

CAUTION

,” “

WARNING

,” and “

DIRECTION

” labels attached to the dryer.

2. Check incoming supply voltage to be sure that it is the same as indicated on the dryer data label affixed to

the upper left side panel area behind the top control (access) door.  In the case of 208 VAC or 240 VAC,
the supply voltage

 

must match

 

the electric service specifications of the data

 exactly

.

3.

GAS MODELS

 - Check to assure that the dryer is connected to the type of heat/gas indicated on the

dryer data label.

4.

GAS MODELS

 - The sail switch damper assembly was installed and adjusted at the factory prior to

shipping.  However, each sail switch adjustment 

must be

 checked to assure that this important safety

control is functioning.  (Refer to sail switch adjustment on 

page 31

.)

5. Check bolts, nuts, screws, terminals, and fittings for tightness and security.

6.

GAS MODELS

 - Be sure that 

ALL

 gas shutoff valves are in the open position.

7. Check 

ALL

 back guard panels and service box covers have been replaced.

8. Check the lint drawer to assure that it is closed and secured in place.

9. Rotate the basket (tumbler/drum) by hand to be sure it moves freely.

10. Check basket (tumbler) bearing setscrews to insure that they are 

ALL

 tight.

11. Check vent is connected to the dryer and is exhausted to the outdoors.

12. There 

should be

 a source of fresh air entering the room.  This source 

should not be

 near where the

dryers exhaust to the outside.

Содержание MDG75V




















































Отзывы:

Нет отзывов