Maytag MAH8700A Скачать руководство пользователя страница 8

Страница: 8 / 13

Troubleshooting Procedures

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.

16026882 8 June

2006

RPL 16026127

Quick Spin Test

While in

Service Mode

, press

Delay

and

Rinse &

Spin

keys to start a

Quick

Spin Test

Quick Spin Test

steps follow:

•

Start spinning, and after reaching a maximum spin
speed.

•

Stay at maximum spin speed for 2 minutes and stop

Quick Spin Test

Hold Quick Spin Step

If the

Rotary Cycle Selector

knob is pressed

during the

Quick Spin Test

, the machine will hold

at the next highest index speed for 10 minutes (1 minute on
early MAH8700’s). At the end of ‘Hold’ time, the machine will
resume and finish the

Quick Spin Test

. To cancel the ‘Hold’

and allow the

Quick Spin Test

to continue, press the

Delay

and

Rinse & Spin

keys.

Fast Time Down Test

While any test or cycle is running in

Service

Mode

, pressing the

Wash/Rinse Temp

key will advance the program to the

next cycle stage. Cycle stages are located at key
locations in the machine operation. As the program is
advanced it will index as follows: The end of each fill (the
same as the beginning of a tumble session for Wash, or
Rinse); at the beginning of a drain session; at the
beginning of a spin session (at this position, check the
water level, if over reset level, drain first before entering
the spin function); at the beginning of a fill session; at the
beginning of Bleach fill; at the beginning of Fabric
Softener fill; and every 3 minutes during the tumble
sessions (Wash and Rinses).

Quick Service Cycle

While in Service Mode, pressing the

Wash/Rinse Temp

and

Soil

Level

keys for

3 seconds will start a

Quick Service Cycle

. This will be a

quick check of all systems. If display shows “

” then open

and close door. Pressing

Spin Speed

key will advance to the

next cycle. The following steps are performed: Display shows
“

”.

1.  Hot water for 5 seconds and then turn off.
2.  Cold water for 5 seconds and then turn off.
3.  Bleach valve for 5 seconds and then turn off.
4.  Softener dispenser using cold water and bleach water for

5 seconds and then turn off.

5. Turn ‘ON’ Cold valves until the control detects proper

water level. During this time, tumble at 45 rpm for 5
seconds in a clockwise direction, pause for 2 seconds,
tumble at 45 rpm for 5 seconds in a counterclockwise
direction, pause for 2 seconds. Continue pattern until the
water level is detected.
Minimum time for this segment to be 5 seconds. After
water height is achieved, continue tumble pattern for
another 14 seconds. If the washer is equipped, turn ‘ON’
heater for first 5 seconds of this tumble pattern. Advance

the washer to next step if water is not connected to
machine.

6. Drain and spin to maximum speed. Machine will achieve

maximum speed using the safest, fastest method.

7. Display a “

” (Passed) continuously for 5 seconds if no

diagnostic codes were logged during the test. Washer will
return to the normal

Service Mode

at the end of the 10

second period.

The “

”

in the display will blink as an indication of

failure,

and continue blinking until the

Quick Service Cycle

test has

reached the end. Any diagnostic code

logged during this test

will result in failure of the test,

but will not necessarily stop the

test.

During the

Quick Service Cycle

, pressing the

Spin

Speed

key will advance to the next step. Pressing the

Rinse

& Spin

and

Spin Only

keys will suspend the

machine at the

current step for up to 10 minutes or

until

Delay

and

Chime

keys are pressed. All

LED

’

s should flash ‘ON’ and ‘OFF’ while

the system is

suspended or on hold.

LED/Switch Test

While in

Service Mode

, press the

Delay

key

to start a

LED/Switch Test

. All the LED’s can be toggled or

slewed by pressing the key associated with the LED or set of
LED’s. All keys (including the

Power Off

button) must be

pressed within 5 minutes for this test to pass. “

” will be

displayed for five (5) seconds once all keys have been
pressed and the test is completed. Following 20 seconds of
inactivity at any point, this test will exit without any display.
The

Power Off

button must be pressed twice within 30

seconds to cancel this test.

Switch Action

Delay

Press once

Chime

Press 3 times

Extra Rinse

Press once

Soil Level

Press 3 times