Maxxus Multipress 10.1 Скачать руководство пользователя страница 13

Страница: 13 / 48

ENG

Assembly – Multipress

Assembly Step 2

Connect the left-hand side frame (2) the right-hand side frame (3) and the rear side frames to the base frame (1) at the

bottom. For this use on each side; 2 hexagonal head screws M10x100 (8), four washers Ø10 (9), two safety nuts M10 (10)

and a curved mounting plate (7). To stick the screws (8) through the frames (2) you will need to lift the traction weights (49)

mounted here in Step 1 as these will otherwise be blocking the drill holes.

With cross beam (28), connect the left-hand side frame (2) and the right-hand side frame (3) to the rear sides at the top. To

do this use two hexagonal head screws M10x20 (34) and two washers Ø10 (9) on each side.

NOTE:

Please only hand tightened all screws until all components are fitting perfectly. Only after this, should the screws be firmly

tightened.

Содержание Multipress 10.1

















































Результаты поиска

Содержание Multipress 10.1

Отзывы:

Похожие инструкции для Multipress 10.1

Бренды по названию

Популярные бренды

Maxxus Multipress 10.1, Руководство по установке

Результаты поиска

Содержание Multipress 10.1

Отзывы:

Похожие инструкции для Multipress 10.1

Бренды по названию

Популярные бренды