background image

   

Page | 10

 

 

 

RECOMMENDED GROUNDING METHOD 

POWER SUPPLY CORD - NOT INCLUDED. 

MUST HAVE A 3-PRONG GROUNDING PLUG. 

For your personal safety, this appliance must be grounded.   To minimize possible shock hazard, the 
cord must be plugged into a mating 3-pronged and grounding-type wall receptacle, grounded in 
accordance with the National Electrical Code and local codes and ordinances.  If a mating wall 
receptacle is not available, it is the personal responsibility of the customer to have a properly 
grounded, 3-prong wall receptacle installed by a qualified electrician.  

 

CONNECTING THE POWER SUPPLY LINE

 

1.

 

Unscrew the two screws holding the access cover and remove the cover. You will find two leads

 

(black and white.) See drawing below.

 

2.

 

Feed a power supply cord (not included) through the access cover and connect it with the two 
leads. The ground line should be connected to the grounding screw. The two connectors must be 

insulated Put the access cover back in place. 

 

3.

 

You will find a strain relief bracket in the accessory package. Fix the power supply cord below the

 

bracket, as shown in the previous illustration. 

 

4.

 

The other end of the power supply cord should be connected to an outlet that is in accordance 

with the local electrical code. 

 

 

Note: This machine is stackable on any of the machines in this manual. 

If the machine is to be stacked 

on top of another machine, a stacking kit will need to be installed. Refer to the installation instructions 
included with the stacking kit.

 

WATER SUPPLY

 

The water supply should be ready at the point of installation. The water supply pressure should be a 
minimum of 15 psig with a static pressure not more than 80 psig.  (A wall outlet directly behind the ice 

maker will make installation easier. 

Tools required: 3/8” open-end wrench and Phillips screwdriver

 

IMPORTANT:

 

1

 

All installations must be in accordance with local plumbing code requirements.  
Professional installation is recommended. 

 

2

 

Water inlet fitting: 3/8” FPT (Female Pipe Thread); drain line connection: 1/2” FPT.

 

3

 

Make certain you have a suitable water supply hose and two suitable drain hoses, and that the 
hoses are not pinched, kinked or damaged during installation 

 

4

 

Check for leaks after connection. 

 

 

Connecting the water line:

 

1

 

Turn off main water supply. 

 

2

 

Find a water supply line near the installation location. The distance should be less than the length 
of the water supply hose. 

 

3

 

A shut-off valve must be installed to the main water supply. 

 

4

 

Connect the water supply hose to tap and water inlet valve.  Tighten firmly by hand, then one-half 
turn with wrench 

 

5

 

Connect the water drain hose to drain line connection.  Tighten firmly by hand, then one-half turn 
with wrench. 

 

6

 

Turn on main water supply and tap. Check for water supply connection leaks. Tighten every 
connection (including connections at the water inlet.) 

 

 

Содержание MIM1000N



















Отзывы: