12
ENGLISH
–
Once the soleplate (13) reaches the set tem-
perature value, the pilot lamp (9) will go out,
you can start ironing.
–
Set the necessary steam intensity with the
continuous steam supply knob (3): «
°
» –
steam is off, «
» – maximal steam intensity.
–
In the continuous steam supply mode, steam
will be released from the openings of the
soleplate (13) only if the iron is in horizontal
position. To stop the steam supply, put the
iron vertically or set the knob (3) to the posi-
tion «
°
» (steam supply is off).
–
After you finish ironing, set the temperature
control knob (11) to the
«OFF»
position, and
the continuous steam supply knob (3) to the
position «
°
» (steam supply is off).
–
Pull the power plug out of the mains socket
and let the iron cool down completely.
ATTENTION!
If steam is not supplied constantly during the
operation, check whether the steam supply knob
(3) is set properly and whether there is water in
the water tank (10).
WATER SPRAY
–
You can dampen the fabric by pressing the
water spray button (5) several times.
–
Make sure that there is enough water in the
tank (10) (that it is filled to one quarter mini-
mum).
BURST OF STEAM
Use the burst of steam function for ironing folds
only at high ironing temperatures (in this case the
temperature control knob (11) is in position «
•••
»
or
«MAX»
).
When the burst of steam button (4) is pressed,
steam will go out of the soleplate (13) openings
intensively.
Note:
To avoid water leakage from the steam
openings, press the burst of steam button (4)
with 4-5 sec. intervals.
To avoid dripping, do not hold down the button
(4) for more than 5 seconds.
The steam is supplied if the tank (10) is filled to
one quarter minimum.
VERTICAL STEAM
The vertical steam function can be used only at
high ironing temperatures (when the temperature
control knob (11) is set to the
«MAX»
position).
Hold the iron vertically at the distance of 10-30 cm
from the clothes and press the burst of steam
button (4) with 4–5 second intervals, steam will
be supplied from the soleplate (13) intensively.
Important information
–
Vertical steam is not recommended for syn-
thetic fabrics.
–
To avoid fabric melting, do not touch it with
the iron soleplate while steaming.
–
Never steam clothes on a person as the
steam temperature is very high, use a clothes
hanger or a stand.
–
After you finish ironing, switch the unit off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
STEAM CHAMBER CLEANING
To prolong service life of the iron, we recom-
mend cleaning the steam chamber regularly,
especially in the regions with hard tap water.
–
Set the continuous steam supply knob (3) to
the position «
°
» (steam supply is off).
–
Fill the water tank (10) up to the “MAX” mark
(12).
–
Place the iron on its base (8).
–
Insert the power plug into the mains socket.
–
Set the control knob (11) to the maximum
temperature
«MAX»
, the pilot lamp (9) will
light up.
–
Once the iron soleplate (13) reaches the set
temperature, the pilot lamp (9) will go out.
Wait until the iron soleplate is reheated, then
you can start cleaning the steam chamber.
–
Unplug the unit.
–
Place the iron horizontally above the sink
and set the knob (3) to the self-clean posi-
tion «
•
».
–
Boiling water and steam with scale will be
released from the iron soleplate (13) open-
ings.
–
Slightly sway the iron back and forth, until
water goes out of the water tank (10).
–
Place the iron on the base (8) and let it cool
down completely.
–
When the soleplate (13) cools down com-
pletely, wipe it with a dry cloth.
–
Before you take the iron away for storage,
make sure that there is no water in the water
tank (10) and that soleplate (13) is dry.
CLEANING AND CARE
MW-3046.indd 12
25.08.2014 14:59:04