Maxwell MW-2312 GY, Инструкция по эксплуатации

Страница: 8 / 20

ENGLISH
8
•
Do not allow children to touch the unit body,
the power cord or the power plug during
operation of the unit.
•
Do not leave children unattended to prevent
using the unit as a toy.
•
Close supervision is necessary when chil-
dren or disabled persons are near the oper-
ating unit.
•
This unit is not intended for usage by chil-
dren. Place the unit out of reach of children
during the operation and cooling down.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (includ-
ing children) or by persons lacking experi-
ence or knowledge if they are not under
supervision of a person who is responsible
for their safety or if they are not instructed
by this person on the usage of the unit.
•
Children can use the unit ONLY under super-
vision of the person, who is responsible for
their safety, and if they are given all the
necessary and understandable instructions
on safety measures and information about
danger, that can be caused by improper
usage of the unit.
•
To avoid damages, transport the unit in the
original package only.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Keep the unit in a dry cool place out of reach
of children and disabled persons.
•
Do not use the unit outdoors.
•
For environment protection do not discard
the unit with usual household waste after its
service life expiration; apply to a specialized
center for further recycling.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
USING THE HOT AIR BRUSH
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
•
Unpack the hot air brush and remove any
stickers that can prevent unit operation.
•
Unwind the power cord completely.
•
Install one of the attachments (8), (9)
or (10). To do this insert the attachment into
the hot air brush body (5) and turn it clock-
wise. If the attachment is set properly, you
will hear the lock button (1) click.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to
the unit operating voltage.
•
Make sure that the operation mode switch
(3) is set to the position “
0 ”.
•
Insert the power plug into the mains socket.
•
Set the required settings of the air flow
using the switch (3):
«
0 » – the hot air brush is switched off;
« 1 » – low speed and low temperature;
« 2 » – high speed and high temperature.
•
The cool shot mode is switched on with
the button (2) equipped with blocking.
To switch the cool shot mode on press the
button (2) and move it towards the attach-
ment. To switch the cool shot mode off
move the button (2) towards the operation
mode switch (3).
•
When the unit is switched on (the switch (3)
is in the position «
1 », « 2 »), the indicator (4)
lights up; when the unit is switched off, the
indicator (4) goes out.
Note: During the first operation some foreign
smell and a small amount of smoke from the
heating element is possible, it is normal.
•
After the hot air brush operation is finished,
switch it off by setting the switch (3) to the
«
0 » position and unplug it.
•
Wait till the hot air brush cools down.
•
To remove the attachment, press the
attachment release button (1) and turn the
attachment counterclockwise.
Overheating protection
Overheating protection switches the hot air
brush off if the outgoing air is too hot. If the
hot air brush is switched off during operation,
set the switch (3) to the «
0 » position, unplug
the unit and make sure that the inlets and
outlets are unblocked. Let the unit cool down
for 5-10 minutes and switch it on again. Do not
IM MW-2312.indd 8 09.12.2016 11:53:25