maxon motor EPOS2 24/5 Скачать руководство пользователя страница 33

Страница: 33 / 44

maxon motor control
EPOS2 Positioning Controller

Document ID: rel5190

4-33

EPOS2 24/5 Hardware Reference

Edition: October 2014

4.7

CAN Connector (J7, J8)

ONNECTION

OSITIONING

ONTROLLER

CAN B

INE

A DS-102

Note

• Consider CAN Master’s maximal baud rate.
• The standard baud rate setting (factory setting) is “Auto Bit Rate”.
• Use termination resistor at both ends of the CAN bus (



chapter “4.8.2 CAN Bus Termination” on

page 4-35).

• For detailed CAN information



separate document «EPOS2 Communication Guide».

Figure 4-29

CAN Connector (J7/J8)

Standard

ISO 11898-2:2003

Max. bit rate

1 Mbit/s

Max. number of CAN nodes

127

Protocol

CANopen DS-301

Identifier setting

DIP switch or software

EPOS2 24/5

CAN 9 pin D-Sub (DIN41652)

Connector [J7] or [J8] Pin [1] “CAN high”

Pin 7 “CAN_H” high bus line

Connector [J7] or [J8] Pin [2] “CAN low”

Pin 2 “CAN_L” low bus line”

Connector [J7] or [J8] Pin [3] “CAN GND”

Pin 3 “CAN_GND” Ground

Connector [J7] or [J8] Pin [4] “CAN shield”

Pin 5 “CAN_Shield” cable shield

Pin

Signal

Description

CAN high

CAN high bus line

CAN low

CAN low bus line

CAN GND

CAN Ground

CAN shield

Cable shield

Accessories

Cables

CAN-COM Cable (275908)
CAN-CAN Cable (275926)
CAN Termination Plug (275937)

Notes

Suitable connector
Suitable crimp terminals
Suitable hand crimper

Molex Micro-Fit 3.0 4 poles (430-25-0400)
Molex Micro-Fit 3.0 female crimp terminals (43030-xxxx)
Molex hand crimper (63819-0000)

Содержание EPOS2 24/5













































Результаты поиска

Содержание EPOS2 24/5

Отзывы:

Похожие инструкции для EPOS2 24/5

Бренды по названию

Популярные бренды

maxon motor EPOS2 24/5, Справочник по аппаратуре

Результаты поиска

Содержание EPOS2 24/5

Отзывы:

Похожие инструкции для EPOS2 24/5

Бренды по названию

Популярные бренды