maxon motor 422969 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

background image

About

About this Document

maxon motor control
ESCON Servo Controller

Document ID: rel5543

1-3

ESCON 70/10 Hardware Reference

Edition: November 2015

© 2015 maxon motor. Subject to change without prior notice.

1

About

1.1

About this Document

1.1.1

Intended Purpose

The purpose of the present document is to familiarize you with the ESCON 70/10 Servo Controller. It will
highlight the tasks for safe and adequate installation and/or commissioning. Follow the described
instructions …

•

to avoid dangerous situations,

•

to keep installation and/or commissioning time at a minimum,

•

to increase reliability and service life of the described equipment.

The document contains performance data and specifications, information on fulfilled standards, details
on connections and pin assignment, and wiring examples.

1.1.2

Target Audience

The present document is intended for trained and skilled personnel. It conveys information on how to
understand and fulfill the respective work and duties.

1.1.3

How to use

Take note of the following notations and codes which will be used throughout the document.

Table 1-1

Notation used

1.1.4

Symbols & Signs

In the course of the present document, the following symbols and sings will be used.

Notation

Meaning

(n)

refers to an item (such as order number, list item, etc.)



denotes “see”, “see also”, “take note of” or “go to”

Type

Symbol

Meaning

Safety Alert

(typical)

DANGER

Indicates an

imminent hazardous situation

. If not

avoided, it

will result in death or serious injury

.

WARNING

Indicates a

potential hazardous situation

. If not

avoided, it

can result in death or serious injury

.

CAUTION

Indicates a

probable hazardous situation

or calls

the attention to unsafe practices. If not avoided, it

may result in injury

.

Prohibited
Action

(typical)

Indicates a dangerous action. Hence,

you must not

!

Mandatory
Action

(typical)

Indicates a mandatory action. Hence,

you must

!

«
1
2
3
4
5
...
»

Содержание 422969









































Отзывы:

Нет отзывов

Похожие инструкции для 422969

Бренд: XBOX Страницы: 4

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: Abicor Binzel Страницы: 8

Бренд: Valor Страницы: 20

Бренд: Datalogic Страницы: 15

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: Vaillant Страницы: 32

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 40

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды