maxon motor 422969 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

Specifications
Standards

maxon motor control

2-10

Document ID: rel5543

ESCON Servo Controller

Edition: November 2015

ESCON 70/10 Hardware Reference

© 2015 maxon motor. Subject to change without prior notice.

2.2

Standards

The described device has been successfully tested for compliance with the below listed standards. In
practical terms, only the complete system (the fully operational equipment comprising all individual com-
ponents, such as motor, servo controller, power supply unit, EMC filter, cabling etc.) can undergo an
EMC test to ensure interference-free operation.

Important Notice

The device’s compliance with the mentioned standards does not imply its compliance within the final,
ready to operate setup. In order to achieve compliance of your operational system, you must perform
EMC testing of the involved equipment as a whole.

Table 2-5

Standards

Electromagnetic Compatibility

Generic Standards

IEC/EN 61000-6-2

Immunity for industrial environments

IEC/EN 61000-6-3

Emission standard for residential, commercial and light-
industrial environments

Applied Standards

IEC/EN 61000-6-3
IEC/EN 55022
(CISPR22)

Radio disturbance characteristics / radio interference

IEC/EN 61000-4-2

Electrostatic discharge immunity test 8 kV/6 kV

IEC/EN 61000-4-3

Radiated, radio-frequency, electromagnetic field immunity
test >10 V/m

IEC/EN 61000-4-4

Electrical fast transient/burst immunity test ±2 kV

IEC/EN 61000-4-6

Immunity to conducted disturbances, induced by radio-
frequency fields 10 Vrms

Others

Environmental
Standards

IEC/EN 60068-2-6

Environmental testing – Test Fc: Vibration (sinusoidal,
10…500 Hz, 20 m/s

2

)

MIL-STD-810F

Random transport (10…500 Hz up to 2.53 g

rms

)

Safety Standards

UL File Number E207844; unassembled printed circuit board

Reliability

MIL-HDBK-217F

Reliability prediction of electronic equipment
Environment: Ground, benign (GB)
Ambient temperature: 298 K (25 °C)
Component stress: In accordance with circuit diagram and
nominal power
Mean Time Between Failures (MTBF): 280'383 hours

«
...
8
9
10
11
12
...
»

Содержание 422969









































Отзывы:

Нет отзывов

Похожие инструкции для 422969

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Samson Страницы: 20

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Dahua Страницы: 58

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды