MAXIMATOR RM350 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 18

background image

RM350

INSTALLATION AND COMMISSIONING

RM350 GAS CONTROLLERS

MAY 16

8 of 18

Interface Signal Connections

Injection Moulding Machine Interface

Mould Closed

This signal is used for safety, and to allow manual and automatic cleaning between cycles. The signal
must be in the CLOSED state for a gas cycle to run.

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Clamp closed; micro switch.

Interlock Signal

This signal is used for safety and the controller will not run a cycle unless this signal is present
(normally closed)

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Safety guard, Purge guard.

Gas Start Signal

This is a DIGITAL START SIGNAL provided by the moulding machine normally via a
relay. The signal is required from the moulding machine at the start of polymer injection.

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Micro switch; Polymer injection

«
...
6
7
8
9
10
...
»

Содержание RM350



















Отзывы:

Нет отзывов

Похожие инструкции для RM350

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: Jeep Страницы: 32

Бренд: Accel Страницы: 8

Бренд: BADODOSECURITY Страницы: 8

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: Quinny Страницы: 21

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Daihan Scientific Страницы: 11

Travel About Series

Бренд: Kolcraft Страницы: 14

Бренд: Miller-Leaman Страницы: 18

Бренд: YASKAWA Страницы: 340

Бренд: Automated Logic Страницы: 10

Бренд: Atmel Страницы: 12

STRATOSTM INSPIRE

Бренд: Ultrahaptics Страницы: 7

Бренд: Consort Страницы: 4

Бренд: Levven Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды