manualshive.com logo in svg

Maxim Integrated MAX32664C, Быстрый старт, Страница: 16 / 24

Поделиться
Скачать
Maxim Integrated MAX32664C Скачать руководство пользователя страница 16

Maxim Integrated 

Page 16 of 24 

2.3.1 Algorithm Settings and Configurations 

The settings shown in 

Table 9

 are available for the WSpO

2

 algorithm. To update the Algorithm 

settings, make sure to send the appropriate commands BEFORE  enabling the algorithm, as 

shown in 

Table 8

. 

Table 9. Configurations and Settings—WSpO

2

 

FAMILY 

BYTE 

ALGORITHM 

INDEX 

CONFIGURATION 

INDEX 

DESCRIPTION 

DEFAULT 

VALUE 

(MSB FIRST) 

0x50 for 

write 

 

 

0x51 for 

read 

0x05 

0x00 

WSpO

2

 Calibration Coefficients x 

100,000 (12 bytes comprised of three 

32-bit signed values) 

0xFFE69196 

000CB735 

00989680 

0x01 

Sampling rate (Hz):  

0x00: 100Hz: 

0x01: 25Hz 

0x01 

0x02 

Algorithm run mode: 

0x00: continuous 

0x01: one-shot 

0x02: calibration (to collect data for 

calibration as in [1]) 

0x01 

0x03 

AGC enable:  

0x00: Disable 

0x01: Enable 

0x01 

0x04 

Motion detection enable:  

0x00: Disable 

0x01: Enable 

0x01 

0x05 

Motion detection period in seconds  

(16-bit unsigned) 

0x0002 

0x06 

Accelerometer motion detection 

threshold in milli-g times 100,000  

(32-bit signed) 

0x01C9C380 

0x07 

AGC timeout in seconds  

(8-bit unsigned) 

0x1E 

0x08 

WSpO

2

 algorithm timeout in seconds 

0x78 

0x09 

Configure the source of the PPG signal 

for the photo detector (PD) 

0x01: PD1 only 

0x02: PD2 only 

0x02 

 
 
 
 
 
 

 

Содержание MAX32664C

























Отзывы:

Нет отзывов