Maxcess MAGPOWR DTR-65 Скачать руководство пользователя страница 37

Страница: 37 / 45

5–5

PARAMETERS

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Miscellaneous

Parameter # Description

Default

P.19

Tension number format
Tells whether tension display is 3-digit with no fixed right-
hand zero or 3-digit with fixed right-hand zero.

0 =

Auto Select between formats. (Based on value in
Maximum Tension C1.3 or C2.5).

1 = 3-digit with no fixed right-hand zero.
2 = 3-digit with fixed right-hand zero.

P.20

Tension polarity
Set to -1 to show positive tension when the force is acting in
the direction opposite the force direction arrow on the load
cells. Set automatically by Precision calibration.

P.21

DP position
Set the decimal point position to show when displaying
tension

0 =  0000
1 =  0000.
2 =  000.0
3 =  00.00
4 =  0.000

P.22

Lock out zeroing tension from [



] button and digital input

when a password has locked the DLCA.

0 =

Zeroing tension allowed when password has locked the
DLCA

1 =

Zeroing tension locked out when password has locked
the DLCA

P.23

Firmware Version. Displays the firmware version.

P.24

Exit from menu and return to displaying tension

Содержание MAGPOWR DTR-65














































Результаты поиска

Содержание MAGPOWR DTR-65

Отзывы:

Похожие инструкции для MAGPOWR DTR-65

Бренды по названию

Популярные бренды

Maxcess MAGPOWR DTR-65, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MAGPOWR DTR-65

Отзывы:

Похожие инструкции для MAGPOWR DTR-65

Бренды по названию

Популярные бренды