Matthews VIAcode T100 Скачать руководство пользователя страница 35

Страница: 35 / 47

T50/T100 PTM – User Guide – Version 2 Issue 1

Maintenance – Ink-Filter Replacement

Ink-Filter Replacement

The

Iink Filter

inside the

Ink-Reservoir

must be replaced every two years or sooner,

dependent upon operating environment. If the PTM is operated in dusty environments it will
require replacement more frequently.

Before starting the following procedure make sure that all warnings and cautions, as listed
under

“Maintenance”

on page 25 are read and adhered to.

Procedure –

Iink Filter

Replacement

1. Close the

Ink-Vent-Screw

2. Clean the

Nozzle-Protector-Plate

with a lint free cloth and then screw it on to the front of

the print head, finger tight. Make sure that it is mounted so the text "Gutter", that is
printed on the plate, is positioned at the bottom of the nozzles. It should be mounted as
shown in Figure 25 on page 30.

3. Make sure that all cables are disconnected and that there is no power supplied to the

PTM.

4. Unscrew and remove the

Ink-Bottle

from the

Ink-Inlet

5. Make sure that the

Ink-Reservoir-Cap

is securely screwed in to the

Ink-Inlet

, so that no

ink is spilt. Then unscrew and remove the five screws that retain the

Reservoir-Cover

Figure 26 - Removing the

Reservoir-Cover

6. Place the PTM so that it is level. Unscrew the

Ink-Reservoir-Cap

and then remove the

Reservoir-Cover.

Screw the

Ink-Reservoir-Cap

back in to its inlet once the cover is

removed.

Reservoir-Cover

Ink-Reservoir-Cap

Содержание VIAcode T100
















































Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды

Matthews VIAcode T100, Руководство пользователя

Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды