background image

17

T50/T100 PTM – User Guide – Version 2 Issue 1

Installation – Mounting the Print Head

• The 

Ink-Resivoir

’s bottom plate, as shown below, is horizontal to the ground and at zero 

degrees to the x axis of the substrate’s face.

Figure 12 - Correct mounting of the print head

• The 

Ink-Resivoir’s

 bottom plate is at zero degrees to the y axis of the substrate’s face.

• The top most nozzle does not tilt either from or towards the approaching substrate’s face. 

The nozzles must be at zero degrees to the z axis.

• The nozzles must be as close as possible (distance D) to the print target 

but not in 

contact

. Refer to Figure 12 above.

• The print head must be protected from contact with the print target. Do not allow the print 

target to contact the print guides as shown below. 

Figure 13 - Print head guides

If necessary, install guard rails to ensure that the print target does not contact the print 
head.

Tilting a Print Head

If the print target does not travel on a horizontal plane, as shown below, the print head’s 
nozzles can be tilted to the left or to the right of the Z axis, so that they are perpendicular to 

D

X = 0°

Z = 0°

Y = 0°

Ink-Reservoir

’s bottom 

plate

Top print guide

Bottom print guide

Содержание VIAcode T100
















































Отзывы: