Matthews Fan Company
Brisa 2000
&
DLC Installation
Instructions
Page 1
3/2/2012
BRISA 2000
With DOWNROD LIGHT CANOPY
READ AND SAVE THESE SAFETY AND INSTAllATION
INSTRUCTIONS.
Consult a licensed electrician
if unsure of any point below mentioned.
DANG ERIW ARNI NG/CAUTION
1.
High voltage and moving parts around motors and motor driven equipment can cause serious or fatal
injuries.
Always disconnect power source at main switch before wiring, servicing or cleaning unit. Do
not rely on fan control device to prevent unexpected start-up or electrical shock.
In addition, power
supply must have fuses or circuit breakers for short circuit protection.
2.
All electrical wiring must conform to national and local electrical codes such as: NEC, OSHA, etc.
3.
Fan should be secure in its electrical grounding to avoid possible electrical shock.
4.
Fan should not be used in any wet or hazardous
location defined
by article 500 of the NEC. In
addition, its ambient temperature should not exceed 104 degrees Fahrenheit.
5.
Power supply should conform to voltage rating of 115V.
6.
Before applying power, visually re-inspect the installation.
Make sure that all guards and protective
devices are securely in place and all visible screws and bolts are tightened.
7.
WARNING:
To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked Acceptable for Fan Support
of
15.9
kg
(35
Ibs) or less
And Use Mounting Screws Provided
With The Outlet Box and/or Support Directly From Building Structure
8.
CAUTION: to reduce the risk of injury to persons, install fan so that bottom edges of fan blades are to
be: In Canada, to satisfy CSA requirements:
at least 8.3 Ft/2.5 M above the floor and all objects in
room if safety cages are utilized.
10.0 Ft if safety cages are not utilized.
In the US, to satisfy UL requirements:
at least 7.0 Ft above the floor and all objects in room if
safety cages are utilized.
10.0 Ft. if safety cages are not utilized.
9.
To reduce the risk of personal injury, do not bend blades or any other part of fan when cleaning.
Do
not insert foreign objects in between rotating fan blades or in space surrounding
entire rotating fan
unit. Fan must be turned off at power at supply source before installation, cleaning or servicing.
10. Instructions
for Supply Connections:
Conductor
of a fan identified
as grounded
conductor
to be
connected
to a grounded conductor
of a power supply, conductor
of fan identified as ungrounded
conductor to be connected to an ungrounded conductor of a power supply, conductor of fan identified
for equipment
grounding to be connected
to an equipment-grounding
conductor.
After making the
wire connections
in junction box, the splices should be turned upward and pushed carefully into the
outlet box.
The wires should be spread apart with the grounded conductor
and the fan-grounding
conductor
on one side of the junction
box and the ungrounded
conductor
on the other side of the
outlet box.
Be sure that all wiring connections
are properly insulated
from each other and any
surrounding
metal parts.
For safety and best operating
results, we recommend
that you have a
qualified electrician assemble and install your fan.
11. To reduce the risk of personal injury, install the supplementary
mounting
means and use only the
hardware provided with the fan.
12. WARNING:
TO REDUCE THE RISKS OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS,
OBSERVE
THE FOllOWING:
A.
Use this unit only in the manner intended by the manufacturer.
If you have any questions,
contact the manufacturer.
B. Before installing, servicing or cleaning unit, switch power off at service panel and lock service
panel to prevent power from being switched on accidentally.
13. WARNING:
To reduce the risk of fire, electrical shock or personal injury, mount to outlet box marked
acceptable for fan support and use screws provided with outlet box.
