Matrix T3X-02 Скачать руководство пользователя

Страница: 53 / 59

10.3 aSSembly iNSTrUCTioNS

aTTeNTioN

After assembly and installation is complete, the treadmill will need to be calibrated using the auto-calibration procedure outlined in Section 3.4.

do NoT stand on the belt while the auto-calibration sequence is in progress.

Prior to assembling the treadmill, unpack all of the contents of the box and make sure that all necessary components are present. Review the

contents of the hardware package for completeness. Contact Matrix customer service at 866.693.4863 to report any missing items.

aSSembly iNSTrUCTioNS

Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure.

To ensure correct assembly of the treadmill, carefully read and follow these steps:

Remove the motor cover(s) and set aside. The motor cover(s) need

to be removed to gain access to the motor compartment so that wire

harness connections can occur.

Open Blue Assembly Bag. Assemble both the left and right console

masts to the treadmill base using item 11 hex head cap screw and

item12flatwasher.Threadtheconsolecablethroughtheright

console mast as you attach it.

CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide

Содержание T3X-02




























































Результаты поиска

Содержание T3X-02

Отзывы:

Похожие инструкции для T3X-02

Бренды по названию

Популярные бренды

Matrix T3X-02, Руководство по обслуживанию

Результаты поиска

Содержание T3X-02

Отзывы:

Похожие инструкции для T3X-02

Бренды по названию

Популярные бренды