manualshive.com logo in svg

Matrix SIMADO GFXD1111S, Системное руководство

Поделиться
Скачать
Matrix SIMADO GFXD1111S Скачать руководство пользователя страница 90

84

Matrix SIMADO GFXD1111S V3 System Manual

Location Information Indication

Location Information Indication feature is used to display the location of installation of SIMADO GFXD1111S, when 
the location information display command is issued. This feature is service provider dependent and must be 
enabled by the service provider so as to use it. Network updates the current location information of the system, 
when the location of installation of the system is changed.

How to Program?

To use this feature, it should be enabled by the service provider. Then the SE shall enable this feature on the 
Mobile Port.

Use following command to enable/disable Location Information Indication on the Mobile Port:

205-Flag-#*

Where,
Flag is:

By default, the Location Information Indication is OFF.

Use following command to display the Location Information on your telephone instrument:

#*-12

•

To display the location information on the LCD of your telephone instrument, the CLI type programmed 
on the FXS Port should be FSK.

•

On issuing the location information display command, if no information is available from the network 
then 'NO LOCATION' message will be displayed.

Relevant Topics:

1.

“Port Parameters-FXS”     116

2.

“Port Parameters-Mobile”     121

Flag Meaning

0

OFF

1

ON

Содержание SIMADO GFXD1111S



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды