Matrix MFU800 Скачать руководство пользователя страница 14

14

Electrical information

Warning! This appliance must be earthed.

The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug.  To change a fuse in this type of plug, follow 
the steps below:

1.  Remove the fuse cover and fuse.

2.   Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.

3.   Replace fuse cover. 

Important: Do not use the appliance without the fuse cover in position.  

How to connect an alternative plug

If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to prevent the risk of 
electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.

As the colours of the wires in the mains lead of this appliance may not correspond with the 

 

 

coloured markings identifying the terminals in your plug, proceed as follows:-

•  

The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the  

 

Earth symbol   

   or coloured GREEN and YELLOW.

•  

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or  

 

 

 

coloured BLACK.

•  

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or    

 

 

coloured RED. 

If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the    
supply cable, the appliance may require removing for servicing.

N.B. Ensure that the plug socket is situated in an easily accessible place.

If the power supply cord is damaged, it must replaced by a CDA authorised agent.

Содержание MFU800

















Отзывы: