Matrix H3XE-01 Скачать руководство пользователя страница 14

Страница: 14 / 81

CHAPTER 5: MANAGER MODE

5.3 MANAGER MODE - TIME TAB

FUNCTION & DEFAULTS

DESCRIPTIONS

MODIFIED

Maximum Time

Default: 60 Minutes

This option allows the club to set the maximum workout

duration limits during peak and non peak hours.

Maximum: 99 Minutes

Minimum: 5 Minutes

Pause Time

Default: 5 Minutes

This option controls the default pause time.

Maximum: 10 Minutes

Minimum: 1 Minute

MANAGER MODE

Time

5.4 MANAGER MODE - DEFAULTS TAB

FUNCTION & DEFAULTS

DESCRIPTION

MODIFIED

Level: Default: 1

This option controls the default program level.

Max: 1 Min: 20

Age: Default: 30

This option controls the default user's age used in the target

HR calculations.

Maximum: 100

Minimum: 10

Weight: Default: 150 lbs

/ 68 kg

This option controls the default weight used in the calorie

calculations. Displayed in pounds or kilograms.

Maximum: 400 lbs / 180 kg

Minimum: 80 lbs / 36 kg

Gender: Default: Male

Setting the user as Male or Female.

Male or Female

Time: Default: 30 Minutes This option controls the default program time.

Max: Max Time Min: 5 Min

MANAGER MODE

Defaults

Содержание H3XE-01


















































































Результаты поиска

Содержание H3XE-01

Отзывы:

Бренды по названию

Популярные бренды

Matrix H3XE-01, Руководство по обслуживанию

Результаты поиска

Содержание H3XE-01

Отзывы:

Бренды по названию

Популярные бренды