Matrix Switch Corporation MSC-XD0816L Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 61

background image

MSC-XD0816L Product Manual

additional details.

•

General Purpose I/O

– A D25 connector provides a GPIO auxiliary port with up to 24 input or output

3.3V logic lines for control and status interfacing with external equipment (LEDs, buttons, etc). See

GPIO Auxiliary Interface

for more details.

1.2 Powering Up The Device

This device is not equipped with a power switch and is simply connected to the power supply adapter which is
plugged into a suitable AC power source, to power it up.
Once the device is powered it goes through the following startup sequence:

•

Reset switch is checked and if it is pressed then the

Software failsafe recovery procedure

is entered.

•

Routing matrix is initialized to Preset 0 state (defaults to source 1 connected to all destinations).

•

The button control panel is initialized and buttons are illuminated to show the initial routing status.

1.3 Front Panel Button Interface

The MSC-XD0816L is equipped with a 16x16 button panel which provides one of several options for
controlling and viewing the status of the routing matrix.
This panel interface provides separate input and output buttons. One output button is active at a time, indicated
by it being lit. The current connection status for the active output is indicated by the relevant numbered input
button being lit. Pressing an input button will cause that input to be connected to the current active output.

1.3.1 Audio Breakaway

An audio breakaway is performed by first selecting the desired output, by pressing the relevant output button,
then pressing and

holding

an input button, followed by pressing another input button. The 1st input button

pressed selects the source of the primary level. The 2nd input button pressed will become the secondary (audio)
source and will flash, indicating a breakaway.

1.4 Web Page Interface

All Matrix Switch Corporation router and panel devices come with a built-in web page interface.
This is the recommended interface for configuration and is also a convenient way to control the matrix routing
of the device.
Devices come factory configured with default settings, unless a pre-configuration request is made during
purchase, an example being a multi device application.

1.4.1 Accessing The Web Page Interface

The default network IP address for this device is 192.168.2.60. Refer to the table below for the default IP
addresses for other types of Matrix Switch Corporation devices.

Page 8 of 61

© 2013-2018 Matrix Switch Corporation

www.matrixswitch

«
...
6
7
8
9
10
...
»

Содержание MSC-XD0816L






























































Отзывы:

Нет отзывов

Похожие инструкции для MSC-XD0816L

Бренд: 3Com Страницы: 8

PathBuilder S200 Series

Бренд: 3Com Страницы: 11

Бренд: 3Com Страницы: 8

CoreBuilder 3500

Бренд: 3Com Страницы: 96

TNS5500D Series

Бренд: 3onedata Страницы: 5

IPS7112G-4GS-8GPOE

Бренд: 3onedata Страницы: 3

Бренд: I-Tech Страницы: 39

PMV WM Ultraswitch

Бренд: Flowserve Страницы: 16

Бренд: PNI Страницы: 92

kontron KSwitch D4 MF

Бренд: S&T Страницы: 100

Бренд: Shinybow USA Страницы: 16

Бренд: Orei Страницы: 27

Бренд: Rackmount Страницы: 16

Hidden Ignition Switch

Бренд: Booma-RC Страницы: 16

Бренд: TE Connectivity Страницы: 32

Бренд: AMBIENTECH Страницы: 4

Бренд: Advantech Страницы: 209

Бренд: Lutron Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды