matev SRM-FB 130 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 22

matev SRM-FB 130 Скачать руководство пользователя страница 3

About this operating manual

Page 3

1

About this operating manual

Dear customer!

Thank you for purchasing this snow blade, we appreciate your trust.

Prior to using this snow blade for the first time read this operating manual carefully and
conscientiously all the way through.

Keep this operating manual where it is easily accessible. This will enable you to refer to
important information and handling instructions as needed.

Listings with bullet points are marked as follows:

•

Text

•

Text

•

Text . . .

Handling instructions are marked in the sequence in which they should be executed, as
follows:

1.

Text

2.

Text

3.

Text . . .

&

This snow blade is subject to change in the interest of technical progress.
All information, illustrations, and technical specifications represent the lat-
est status at the time this manual was published. The manufacturer reserves
the right to make changes at any time in the interest of technical progress.

«
1
2
3
4
5
...
»

Содержание SRM-FB 130























Отзывы:

Нет отзывов