Matelec FPC-15007-CON, Руководство владельца

Страница: 3 / 12

3
FRONT SIDE VIEW
Top
Bottom
Top
Bottom
DOC: APP 15005
VER 1.0
WIRING CONNECTION DETAIL
FPC-15006-CON
ON STEADY
Pump contacts are switched ‘On’
SLOW FLASH
Pump run has been interrupted by a control circuit
ON STEADY
Pump is in auto mode and will start upon inputs from level switches
SLOW FLASHING
Pump has been interrupted by ‘maximum run time’ feature
ON STEADY
A high level is or has been present
FLASHING SLOWLY
A low level is or has been present
ON STEADY
The thermal overload protection on the pump circuit has been tripped and requires
manual reset
ON STEADY
Pump is in manual mode and will run continuously regardless of level switch status for a
prescribed period only
TO RESET FAULT, PRESS MUTE BUTTON FOR 3 SECONDS
AN ACKNOWLEDGEMENT BEEP WILL SOUND WHEN FAULTS ARE CLEARED
POWER ON
Light will illuminate when there is power connected to the panel and the main isolator
switch is switched on
MUTE
Press to silence buzzer
Press and hold for 3 seconds to clear faults
Press and Hold for more than 3 seconds to test buzzer and strobe
WARNING: HIGH VOLTAGE
ALL ELECTRICAL CONNECTIONS MUST BE CARRIED OUT
BY A SUITABLY QUALIFIED ELECTRICIAN
ACCESS BY AUTHORISED PERSONNEL ONLY
OVERLOAD
MUTE
MAN
WIRING CONNECTION DETAIL
APP-15005
ON STEADY
Pump contacts are switched ‘On’
SLOW FLASH
Pump run has been interrupted by a control circuit
ON STEADY
Pump is in auto mode and will start upon inputs from level switches
SLOW FLASHING
Pump has been interrupted by ‘maximum run time’ feature
ON STEADY
A high level is or has been present
FLASHING SLOWLY
A low level is or has been present
ON STEADY
The thermal overload protection on the pump circuit has been tripped and requires
manual reset
ON STEADY
Pump is in manual mode and will run continuously regardless of level switch status for a
prescribed period only
TO RESET FAULT, PRESS MUTE BUTTON FOR 3 SECONDS
AN ACKNOWLEDGEMENT BEEP WILL SOUND WHEN FAULTS ARE CLEARED
POWER ON
Light will illuminate when there is power connected to the panel and the main isolator
switch is switched on
MUTE
Press to silence buzzer
Press and hold for 3 seconds to clear faults
Press and Hold for more than 3 seconds to test buzzer and strobe
WARNING: HIGH VOLTAGE
ALL ELECTRICAL CONNECTIONS MUST BE CARRIED OUT
BY A SUITABLY QUALIFIED ELECTRICIAN
ACCESS BY AUTHORISED PERSONNEL ONLY
OVERLOAD
MUTE
MAN
INDICATOR LIGHTS GUIDE INDICATOR LIGHTS GUIDE
SET THERMAL OVERLOADS TO SUIT PUMP
240Vac
MAINS POWER
SUPPLY
STOP/LOW
LEVEL
FLOAT SWITCH
START/MEDUIM
LEVEL
FLOAT SWITCH
HIGH ALARM
LEVEL
FLOAT SWITCH
COMMON
N/O C
LOSE ON RISE
COMMONCOMMON
N/O C
LOSE ON RISE
COMMON
N/O C
LOSE ON RISE
PUMP 240Vac
INPUT 2
STOP
LEVEL
START
LEVEL
HIGH
LEVEL
INPUT 3 INPUT 4
COMMON
FAULT
Volt/Free
BMS
PUMP SUPPLY
FLOAT SWITCH CONNECTIONS
12Vdc CONNECTIONS 240Vac CONNECTIONS
BLUE NOT
REQUIRED
E A N E A N
Probe Holder
s/s Probe rodes
PUMP
415Vac
415Vac
MAINS POWER
SUPPLY
COMMON
FAULT
Volt/Free
BMS PROBES
E1
COMMON
E1
Stop
E2
Start
E3
High
Low/Voltage
SUPPLY
415Vac CONNECTIONS
A2 A3 N E A1
PUMP
P2 P3 E P1 T1 T2
Therm.
12Vdc
BRIDGE
IF NOT
REQUIRED
Mounting
Frame/
Wall
INSTALLATION
CONNECTION
MOUNTING
1. Controller enclosure must be
mounted in a vertical position.
2. Ensure mounting method does
not compromise enclosure
weather proof rating.
3. Ensure access to main isolator is
not restricted.
4. Ensure cables/conduits entering
the panel have mechanical
protection and that the
penetrations are sealed and do
not compromise the weather
proof rating of the enclosure.
Note:
Controller must be earthed and all electrical connections must be carried out by a suitably qualified
Electrician.
MAIN ISOLATOR