Radio Equipment Directive (RED)
2014/53/EU
Article 3.1(a) Health
EN62479:2010
EU Directives
Conformas to
2011/65/EU and its amendment
2015/863/EU (ROHS)
ROHS 2011/65/EU and its amendment
2015/863/EU
2009/125/EC ERP
ERP:
EN 50564:2011
Article 3.2 Radio:
EN 300 220-1 V3.1.1 (2017-02)
EN 300 220-2 V3.1.1 (2017-02)
Article 3.1(b) EMC:
Draft EN 301 489-1 V2.2.0 (2017-03)
EN 301 489-3 V2.1.1 (2019-03)
Article 3.1(a) Safety:
EN62368-1:2014+A11:2017
This product belongs to receiver category 2
: Caution
Warning: Risk of explosion if the battery is replaced by an incorrect type.
Push Button
This product contains a coin/button cell battery and if ingested can cause severe chemical burns. If the battery has been ingested, please
seek medical advise immediately. In just 2 hours a digested battery can lead to death. Keep new and used batteries away from children. If
the battery compartment does not close securely, please stop using the product.
IP44: Protect from ingress of solid object which diameter greater than 1mm and splash water proof.
Direct current (DC Power)
Push Button Battery:
1 x 3V CR2032
Push Button:
IP44
Melody Count:
2
Sound Level:
80dB
Technical Data
Chime Battery:
220-240V~
Radiated Power:
8mW
Temperature:
Max. 40°c
Range:
30M (open area)
Frequency:
433.92MHz
Unique Code Selection
The door chime and push button will be paired straight of the box, with 1 out of 1 million unique codes to prevent interference with another
door chime. If the door chime does not sound, please refer to the ‘Pairing Additional Push Buttons & Door Chimes’ section.
Chime Selection
Single press the melody button on the left of the door chime to filter through the two different options – ‘Ding-dong’ and ‘Westminster’ chimes.
Volume Selection
Single press the volume selection button to filter through the four different volumes settings - mid (default) > high > mute > low
Pairing Additional Push Buttons & Door Chimes
To pair an additional push button to the door chime, unplug or switch off the socket to power down the door chime. Re-insert or switch on the
chime and press the push button after the first ‘beep’ and before the second double ‘beep’. (A maximum of 16 push buttons can be paired).
Reset Door Chime
Press and hold the melody button for 10 seconds or until you hear a triple ‘beep’ to reset the door chime.
Door Chime Not Working?
1. Ensure new batteries are being used in both the door chime and push button
2. Check if the battery polarity in the door chime and push button is correct
3. Objects and materials, such as walls, doors, ceilings and furniture, could be blocking the signal. Try moving the chime closer to the push
button. Maximum distance is based on an open area environment. Any walls, doors or ceilings may reduce the operating range. Door chime
is to be used indoors only.
4. Wireless interference can be caused by external wireless devices, such as alarms and adaptors. Try moving away from these devices.
5. Door chime and push button are not paired-please refer to the ‘Pairing Additional Push Buttons’ secion.
6. Ensure the socket is switched on.
IMPORTANT
This product does not consist of any serviceable parts and should not be repaired. The device should not be operated by persons who have
a lack of experience or knowledge in using such products. People who have a reduced physical, sensory or mental capability should be
supervised or given instruction when operating. Childen should be supervised, so that they do not play with the device.
