To open the door
manually:
The door should be fully
closed if possible. Pull
down on the red manual
release handle and lift
the door manually. To
reconnect the door to the
opener, press the Door
Control push bar.
32
Activate opener with any of the following:
1. The Remote Control: Hold the large push button
down until the door starts to move.
2. The Door Control: Hold the push bar down until the
door starts to move.
3. The Outside Keylock or Keyless Entry System.
(See Accessories.)
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for entry
and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The door will reverse in the closing cycle, and the
opener lights will blink for 5 seconds, when the
invisible beam is broken. If fully open, the door will not
close when the beam is broken. The sensor has no
effect in the opening cycle.
If the sensor is not installed or not aligned correctly, the
door won’t close from any remote control transmitter. You
can close the door with the Door Control, the Outside
Keylock, or Keyless Entry, however, if you activate them
until down travel is complete. If you release them too
soon, the door will
reverse.
The Opener Lights will turn on under the following
conditions: when the opener is initially plugged in; when
the power is interrupted; when the opener is activated. It
will turn off automatically after 4-1/2 minutes, or provide
constant light when the Light feature on the Multi-
Function Door Control is activated. Bulb size is 75 watts
maximum.
Lights will also turn on when someone walks through the
open garage door. With a
Multi-Function Door Control,
this feature may be turned off as follows: With the opener
lights off, press and hold the light button for 10 seconds,
until the light goes on and off again. To restore this
feature, start with the opener lights on, then press and
hold the light button for 10 seconds.
The lockout feature
prevents the trolley from
reconnecting automat-
ically. Pull the manual
release handle down and
back (toward the opener).
The door can then be
raised and lowered
manually as often as
necessary.To disengage
the lockout feature, pull
the manual release
handle straight down. The
trolley will reconnect on
the next UP or DOWN
operation.
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down)
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down & Back
Towards Opener)
Lockout position
Manual disconnect
position
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the manual release
rope and handle
only when door is fully closed.
Operation of Your Opener
WARNING
Door Control Push Bar: Press the white square to open or
close the door. Press again to
reverse the door during the
closing cycle or to
stop the door while it's opening.
Light Feature: Press the Light button. If the opener light
is
off, it will turn on. If the opener light is on, (even in the 4-
1/2 minute automatic cycle) it will turn
off.
But if you use the Light button to turn the lights
on and
then activate the opener, the lights will turn
off after
4-1/2 minutes.
The 4-1/2 minutes interval can be changed to 1-1/2,
2-1/2, or 3-1/2 minutes as follows: Press and hold the
Lock button until the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes.Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
The Light button will not control the opener lights when the
door is in motion.
Lock Feature: The Lock feature is designed to prevent
operation of the door from remote controls. However, the
door will
open and close from the Door Control push bar,
the Outside Keylock and the Keyless Entry Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar light will flash as long as the
Lock feature is
on.
To turn off: Press and hold the Lock button again for 2
seconds. The push bar light will stop flashing. Normal
operation will resume. The Lock feature will also turn off
whenever the “Smart” button on the opener panel is
activated.
Operation of the Multi-Function Door Control
(See additional programming features, next page.)
