MasterCraft Hawkeye Laser 054-8347-0, Инструкция по эксплуатации

Страница: 6 / 18

7 1/4" CIRCULAR SAw wITh LASeR LINe - 054-8347-0 7 1/4" CIRCULAR SAw wITh LASeR LINe - 054-8347-0
9 10
additional safety instructions for operation
WARNING!
Keep hands and body away from and to the side of the blade. Contact with blade will result
in serious injury.
WARNING!
To reduce the risk of injury, user must read instruction manual. Check lower guard. It must
cover the blade instantly! hold saw with both hands. Support and clamp work. wear eye
protection.
WARNING!
Be sure to read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
• Know your power tool.
Read the Owner’s Manual carefully. Learn the applications and the specific
potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or
serious injury.
• Protect your hearing.
wear appropriate personal hearing protection during use. Under some
conditions, noise from this product may contribute to hearing loss.
• Always wear safety glasses. everyday eyeglasses have only impact-resistant lenses; they are
NOT safety glasses. Following this rule will reduce the risk of serious personal injury.
• Protect your lungs. wear a face or dust mask if the operation is dusty. Following this rule will
reduce the risk of serious personal injury.
• All visitors and bystanders must wear the same safety equipment as the operator
.
• Only use saw blade recommended; do not use any abrasive wheels
.
• Inspect the tool cords periodically, and if damaged, have them repaired by a qualified service
technician. Be aware of the cord location.
• Always check the tool for damaged parts. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine whether it will operate properly and
perform its intended function. Check for misalignment or binding of moving parts, broken parts, and
any other condition that may affect the tool’s operation. A guard or other part that is damaged should
be properly repaired or replaced by a qualified service technician.
• Save these instructions.
Refer to them frequently, and use them to instruct others who may use
this tool. If someone borrows this tool, make sure they have these instructions also.
• When restarting a saw in the work piece, centre the saw blade in the kerfs and check that
saw teeth are not engaged into the material.
If saw blade is binding, It may walk up or kickback
from the work piece as the saw is restarted.
• Support large panels to minimize the risk of blade pinching and kickback.
Large panels
tend to sag under their own weight. Supports must be placed under the panel on both sides, near the
line of cut and near the edge of the panel.
• Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerfs
causing excessive friction, blade binding and kickback.
• Blade depth and bevel adjusting locking levers must be tight and secure before making
cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
• Use extra caution when making a ‘plunge cut’ into existing walls or other blind areas.
The
protruding blade may cut objects that can cause kickback.
SaFetY inStruCtiOnS FOr SawS with the lOwer BlaDe GuarD
• Check lower guard for proper closing before each use. Do not operate the saw if lower
guard does not move freely and close instantly. Never clamp or tie the lower guard into
the open position.
If saw is accidentally dropped, lower guard may be bent. Raise the lower guard
with the retracting handle and make sure it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
• Check the operation of the lower guard spring. If the guard and the spring are not
operating properly, they must be serviced before use. Lower guard may operate sluggishly
due to damaged parts, gummy deposits, or a build-up of debris.
• Lower guard should be retracted manually only for special cuts such as’ plunge cuts’ and
‘compound cuts’. Raise lower guard by retracting handle and as soon as blade enters
the material, the lower guard must be released.
For all other sawing, the lower guard should
operate automatically.
• Always observe that the lower guard is covering the blade before placing saw down
on bench or floor.
An unprotected, coasting blade will cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.
Sa
Fe
tY G
ui
Deline
S
Sa
Fe
tY G
ui
Deline
S