MasterCraft 062-3535-2 Скачать руководство пользователя страница 6

Страница: 6 / 17

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS

MOTOR AND ELECTRICAL

SKU number

062-3535-2

I
Solids handling

1/4” (6.3 mm) spherical

Upper bearing

Ball bearing

Lower bearing

Ball bearing

Motor protection Auto-reset thermal overload protection in motor

Maximum flow 3600 U.S. GPH (13,627 L/hr)
Maximum head height 28' (8.5 m)

Construction material

Aluminum alloy for motor house; plastic for volute and
impeller

Plastic

Liquid temperature range 32 to 95°F (0 to 35°C)

Single phase Permanent split capacitor (PSC)

Motor NEMA L, torque curve, oil-filled, squirrel cage induction,
class B insulation

Seal Lip seal

Discharge size 1 1/2" (3.8 cm) female national pipe thread (FNPT)
or 1 1/4" (3.2 cm) FNPT (with adaptor)

Cord length 10' (3 m)

Cord size 18 AWG

115 V AC

Power

R
Full load amps

7.6

Cord type SJTW

NOTE:

Do not reduce size of discharge pipe or hose below 1 1/4" (3.2 cm) diameter.
If discharge is too small, pump will overheat and fail prematurely.
This pump is designed for use in a residential sump only. Only pump
water with this pump.

model no. 062-3535-2 | contact us 1-800-689-9928

Содержание 062-3535-2


















Результаты поиска

Содержание 062-3535-2

Отзывы:

MasterCraft 062-3535-2, Инструкция по эксплуатации, Страница: 6 / 17

Результаты поиска

Содержание 062-3535-2

Отзывы: