manualshive.com logo in svg

Master Spas Bar Harbor, Руководство пользователя, Страница: 69 / 72

Поделиться
Скачать
Master Spas Bar Harbor Скачать руководство пользователя страница 69

America’s Leader In Luxury

M A S T E R   S P A S

69

REGULAR MAINTENANCE PROCEDURES

CIRC PUMP DISCHARGE FITTING NEEDS TO BE CLEANED

The circ pump discharge screen should be removed and cleaned if your spa is 
equipped with a circ pump.This screen can get clogged up due to mineral 
deposit or debris. It should be cleaned at least once every 180 days or when 
the spa is drained.
Directions to remove the screen:

With the power to the spa off, remove the two screws holding the 
screen in place. Soak the screen in white vinegar and rinse thoroughly 
with water.
Clean out any debris that you may see clogging the fitting under the screen
and reinstall the screen.

REPLACING YOUR LIGHT BULB

If your light bulb goes out, it is very easy to replace.
Use a 12 volt, 6 watt bulb that should be available through your dealer.
First, make sure the power to the spa is off.You can access the spa light fitting 
by removing the spa panel.
Once the panel is removed, unfasten the black fitting inside the white 
light assembly, by turning it counter clockwise.
Attached to the black fitting is the light bulb. Replace the bulb and reinsert 
the fitting, by turning it clockwise.
If the white lens cap needs to be removed, insert a flat head screw driver as 
shown in the picture below.

This may also be necessary when installing
an LED light.

MS Owners Manual  12/5/03  2:06 PM  Page 69

Содержание Bar Harbor









































































Отзывы:

Нет отзывов