8. Remove the thermal carafe to serve when brewing is finished (about one minute later after the
coffee stops dripping).
Note: The coffee you get will be less than the water you have added, as some water is absorbed
by the coffee grounds.
9. The appliance will turn off power automatically at the completion of brewing. For an
optimum coffee taste, serve it just after brewing.
10. Always turn the coffee maker off and disconnect the power supply when not use.
NOTE: Use caution when pouring coffee as the temperature will be high and may cause burns.
1. Fill the water tank with water and descaler to the MAX level as indicated in the water tank.
(The scale of water and descaler is 4:1, the detail refers to the instruction of descaler. Please use
“household descaler”, you can use the citric acid instead of the descaler (use one hundred parts of
water and three parts of citric acid).
2. Put the thermal carafe on the heat insulation plate and ensure it is placed in position.
3. Press the button once and red POWER/EN MARCHE indicator light will come on. After a while,
water will drop out automatically.
4. After running the equivalent of one cup, turn the coffee maker off by pressing the button again.
5. Leave the solution to soak for 15 minutes. Repeat steps 3 to 5.
6. Turn the appliance on by pressing the ON/OFF button once and run the remaining until the water
tank is completely empty.
7. Rinse by operating the appliance with water at least 3 times.
DELAY BREW
CLEANING YOUR COFFEE MAKER
Model no.043-5757 | Contact us: 1-855-803-9313
HINTS FOR GREAT-TASTING COFFEE
REMOVING MINERAL DEPOSITS
DELAY BREW
If you do not want the coffee maker to start operation immediately, for example now it is 8:10 a.m.,
you would like the coffee maker to start automatically at 1:10 pm, first follow steps 1 to 5 of previous
section, and then set the automatic start function as follows:
1. Press AUTO/PROG button once, LCD will show the automatic starting time and the green
AUTO/PROG indicator light will flash.
2. Press the HOUR/HEURE and MIN button to set the automatic starting time, that is 1:10 p.m.
Note: the time cycle is 12 hours.
3. Press AUTO/PROG button once again and the green indicator will go out.
4. Press and hold AUTO/PROG button for 3 seconds, and the green AUTO/PROG indicator light will
remain on.
5. When the time is due, the green AUTO/PROG indicator light will go out and the red POWER/EN
MARCHE indicator light will come on, and the coffee maker will start brewing. starts brewing.
When brewing is completed, 3 buzzer sounds will be heard .
HINTS FOR GREAT-TASTING COFFEE
1. A clean coffee maker is essential for making great-tasting coffee. Regularly clean the coffee maker
as specified in the "CLEANING YOUR COFFEE MAKER" section. Always use fresh, cold water in the
coffee maker.
2. Store unused coffee grounds in a cool, dry place. After opening a package of coffee grounds, reseal
it tightly and store it in a refrigerator to maintain its freshness.
3. For an optimum coffee taste, buy whole coffee beans and finely grind them just before brewing.
4. Do not reuse coffee grounds as this will greatly reduce the flavour of the coffee. Reheating coffee
is not recommended as coffee is at its peak flavour immediately after brewing.
5. Clean the coffee maker when over-extraction causes oiliness. Small oil droplets on the surface of
brewed, black coffee are due to the extraction of oil from the coffee grounds.
6. Oiliness may occur more frequently if heavily roasted coffees are used.
REMOVING MINERAL DEPOSITS
To keep your coffee maker operating efficiently, you should clean away the mineral deposits left by
the water regularly according to the water quality in your area and the frequency use of appliance,
the detail is as follows:
CLEANING AND MAINTENANCE
CAUTION:
Be sure to unplug this appliance before cleaning. To protect against electrical shock,
do not immerse cord, plug or unit in water or liquid. After each use, always make sure plug is first
removed from wall outlet.
1) Clean all detachable parts after each use in hot, sudsy water.
2) Wipe the product’s exterior surface with a soft, damp cloth to remove stains.
3) Water droplets may buildup in the area above the funnel and drip onto the product base during
brewing. To control the dripping, wipe off the area with a clean, dry cloth after each use.
4) Use a damp cloth to gently wipe the heat insulation plate. Never use abrasive cleaner to clean it.
5) Replace all parts and keep for next use.
Model no. 043-2742-0 | Contact us: 1-855-803-9313
TM
