Mastech MY-60 Скачать руководство пользователя страница 11

Страница: 11 / 17

1.4 MAINTENANCE

* Before opening the meter, always disconnect test leads from all sources of electric

current.

* For continue protection against fire, replace fuse only with the specified and current

rating: F200mA / 250V (quick acting)

*If any faults or abnormalities are observed, the meter can not be used any more and

it has to be checked out.

*Never use the meter unless the back cover is in place and fastened fully.

*Do not use abrasives or solvents on the meter use a damp cloth and mild detergent

only.

-4-

1. DESCRIPTION

This meter is one of a series portable professional measuring instrument, capable of

performing functions:

－

DC and AC voltage measurement

－

DC and AC current measurement

－

Resistance measurement

－

Capacitance measurement

－

Diode and Transistor test

－

Audible continuity test

Some models of this series also provide functions:

－

Temperature measurement

－

Frequency measurement

-5-

Содержание MY-60


















Результаты поиска

Содержание MY-60

Отзывы:

Похожие инструкции для MY-60

Бренды по названию

Популярные бренды

Mastech MY-60, Руководство оператора

Результаты поиска

Содержание MY-60

Отзывы:

Похожие инструкции для MY-60

Бренды по названию

Популярные бренды