0. Introduction - Specifications
Workshop Service Manual for CENTORA 7280-7282 Combine Range - EN_D3111800M2
21
0.6
Start-up instructions
0.6.1
General
To ensure that the machine is maintained regularly during
the warranty period, head office or the local AGCO dealer
and supplier must arrange for a service inspection after 50
hours of operation and after the first harvest.
This inspection has been introduced and is designed to
ensure that the machine gives optimum performance
throughout the warranty period, with the result that it will
operate reliably for many years to come.
0.6.2
Pre-delivery checks
Prior to delivery to the dealer and delivery from the dealer
to the customer or transfer to the user, head office must
ensure that the following is done:
BEFORE INSPECTION
•
Check the combine/cutting table/table trailer and
equipment for transport damage.
•
Check that the combine has been delivered in accord-
ance with the order/delivery specification.
•
Verify and register the serial numbers on the combine,
engine, cutting table and yieldmeter source (if fitted).
•
Fit any parts that were removed before transport.
•
Fit any optional equipment ordered (if it was not fitted
at the factory).
FLUID LEVEL CHECK
Check the various fluid levels and top up if necessary:
1. Cooling system, antifreeze 50%
2. Fuel tank.
3. Engine oil.
4. Gearbox.
5. Final drives.
6. Hydraulic oil tank(s).
7. Brake fluid tank.
8. Wobble box (knife drive).
9. Right-angle gear for returns thresher.
10. Battery acid level and cable shoe.
LUBRICATION
Lubricate the following points:
11. All grease nipples.
SETTINGS
Fit the cutting table in accordance with the operator’s
manual. Check and adjust if necessary:
12. Main crop elevator/chains.
13. Check tightening of all air-intake hoses/pipe connec-
tions on the engine.
14. Make sure that hoses, pipes and lines are not close to
the exhaust system, belt pulleys, belts, etc.
15. Check the tightening of hoses and connections in the
cooling system.
16. Slip clutches for main crop elevator/returns system,
after dismantling and cleaning.
17. Check that the clutch for the cutting table/table auger
does not slip, after dismantling and cleaning.
18. Concave setting.
19. Rotary separator concave setting.
20. Rear beater curtains.
21. Check hydraulic connections for leaks. Repair if nec-
essary.
22. All belts and chains.
23. Seals for stone trap/main grain pan and shaker shoe.
24. Function and setting of straw chopper clutch.
25. Tightening of bolts in wheels and undercarriage in
accordance with operator’s manual.
26. Tyre pressure in accordance with operator’s manual.
BEFORE STARTING THE ENGINE
Turn on the ignition and check:
27. That the pilot lamps for oil pressure and ignition come
on.
28. Lights - main lights, direction flashers, warning lights
and horn.
29. Operating DATAVISION .
30. Select and check: "Combine type" / "Equipment setup"
/ "Equipment type" and "Gear ratio".
STARTING THE ENGINE
Start the engine and check:
31. That the pilot lamps for oil pressure and ignition go
out.
32. Cooling water temperature sensor (if fitted).
33. Operation of throttle lever.
34. That the fuel stop function stops the engine.
WHILE THE ENGINE IS RUNNING
do the following:
The combine must be kept under constant observation
and checked for faults/leaks during this testing.
35. Check the threshing unit and cutting table at low
speed. Then let the threshing unit run for 30 minutes
at max. speed and check all the functions. The reel
should run at half speed.
36. Check table reversing at low engine speed.
37. Check operation of hydrostatic transmission, speed
control/gearshift and brakes.
38. Check all electrical/hydraulic functions/control sys-
tems.
39. Check mechanical/electric clutches.
40. Check max./min. speed of reel/threshing cylinder and
fanning mill.
41. Check engine and straw walker speed.
