Masport HXL15V Скачать руководство пользователя страница 5

INTENDED USE 

 

Masport Vacuum / Pressure Pumps are intended to be used for loading and unloading of 
liquid material.  These pumps are commonly used for liquid waste transport, septic tank 
cleaning, oil field service work, car wash or grease trap cleaning and many other 
industrial applications. 

WARNING! 

Masport pumps must not be used to move flammable or highly 
caustic material.  Use of this pump for moving hazardous material 
may result in machinery failure, bodily injury or even death. 

 
 

SETUP 

 
The 4-way valve on the pump is used to change the pump operation from vacuum to 
pressure or pressure to vacuum by rotating the handle 90 degrees.  Either side of the 
valve can be plumbed as the intake or exhaust port.  Depending on how it is plumbed, 
the vacuum or pressure indicators on the top of the valve may be reversed. 
 
When designing the system in which this Masport pump will be installed it is important to 
make sure all of the components and plumbing are of adequate size. 
 

NOTE! 

Using components or plumbing with a smaller I.D. than 
recommended for a particular pump will result in poor system 
performance and may damage the pump. 

 
The HXL75 model pumps are designed with 2 1/2" NPT ports.  Any components, hose or 
fittings with a smaller I.D. will restrict air flow and may damage the pump. 
 
The HXL15 and HXL400 model pumps are designed with 3" NPT ports.  Any 
components, hose or fittings with a smaller I.D. will restrict air flow and may damage the 
pump. 
 

NOTE! 

Before assembling the system, make sure the inside surfaces of all 
pipes, hose and fittings are clean and free of any kind of dirt or 
debris.  Any solid particles ingested by the pump may result in 
higher operating noise, loss of performance or irreparable pump 
damage. 

 
Some form of pipe sealant should be used on all thread connections to prevent leaks. 
 

HOSE 

Any hose used in your system should be rated for at least 28" hg vacuum and 25 PSIG 
pressure.  It will also need to withstand an oil/air mixture at temperatures up to 300° F.  
"Hot Tar and Asphalt" hose is designed for use in this type of environment.

 

Содержание HXL15V



























Отзывы: