masosine SPS 100 Скачать руководство пользователя страница 58

Страница: 58 / 139

Dismantling the pump housing—SPS 200 pumps with a stainless steel power frame and a single
mechanical seal

Note

: See "Dismantling the pump housing—SPS 200 pumps with a cast iron power frame and a single

mechanical seal" on page 54 for dismantling the pump housing of a pump with a cast iron power frame.

•

Use a 13mm spanner to loosen and remove the six screws (right-hand thread) and washers which
secure the pump housing to the power frame.

•

If necessary, gently tap the pump housing with a soft hammer to free it. Withdraw the pump

housing carefully.

The pump housing is heavy.

•

Pull off the flush ring. Whichever flush ring is installed, the procedure is the same.

Dismantling the pump housing—SPS 200 pumps with a stainless steel power frame and a triple
lip seal

•

Remove the distance ring from the flush ring.

Assembling the SPS 200

Note

: The pictures show a pump with a cast iron power frame. Assembly of models with stainless steel

power frame is similar. For exceptions, see "Assembling the pump housing— SPS 200 pumps with a
stainless steel power frame" on page 63

During assembly, check that all O-rings are properly positioned before fitting each component, and that
all components are clean and lubricated.

m-SPS-en-08

Содержание SPS 100












































































































































Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды

masosine SPS 100, Руководство пользователя

Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды