masosine SPS 100 Скачать руководство пользователя страница 63

Страница: 63 / 139

Note

: The pump housing may be positioned in three orientations. See "Possible pump orientations" on

The pump housing is heavy.

•

Fit the two 13mm screws (right-hand thread) and washers which secure the pump housing to the

power frame. 10-2 assembly is shown here. Alternative screw positions (three of four arrowed)
allow the pump housing to be positioned at 9-12 or 12-3 orientations. Tighten to 35Nm.

Assembling the pump housing—SPS 200 pumps with a stainless steel power frame

Note

: See "Fitting the pump housing—SPS 200 pumps with a cast iron frame and a single mechanical

seal" on page 60 for assembling the pump housing of a pump with a cast iron power frame.

•

Fit the flush ring. Whichever flush ring is installed, the procedure is the same. For single mechanical
seal system the distance ring is not needed.

•

Position the pump housing carefully.

The pump housing is heavy.

•

Use a 13mm spanner to fit and tighten the screws (right-hand thread) and washers which secure

the pump housing to the power frame.

Assembling the distance ring—SPS 200 pumps with a stainless steel power frame and a triple lip
seal

•

Fit the distance ring into the flush ring before fitting the flush ring.

m-SPS-en-08

Содержание SPS 100












































































































































Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды

masosine SPS 100, Руководство пользователя

Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды