Masoneilan SVI II ESD Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 220

Masoneilan SVI II ESD Скачать руководство пользователя страница 73

Masoneilan SVI II ESD Installation and Maintenance Manual

=

|

73

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Connecting the Tubing and Air Supply

NOTE

It is advisable to tube and apply the air supply to the SVI II ESD
before connecting the electrical input signal to power it up.

NOTE

For small actuators it may be necessary to use 1/8" tubing for
Autotune to work properly.

This section describes the process for connecting the tubing and air supply to a single acting
PST controller.

Pneumatic Connections

The SVI II ESD is intended for use with industrial compressed air or natural gas systems only
that meet the requirements of ISA standard 7.3. Supply pressure must not exceed 120 psi. A
coalescing filter can be used to assure that the supply air is sufficiently free of oil, water, and
particulate contaminants. Ensure that an adequate pressure relief provision is installed when
the application of system supply pressure could cause peripheral equipment to malfunction.
Installation must be in accordance with local and national compressed air and
instrumentation codes. Table 7 provides the pneumatic connections and air supply
requirements for the SVI II ESD.

Table 7 Pneumatic Connections/Air Supply Requirements

Recommended Piping
Inlet/Outlet

1/2” stainless steel or PVC tubing. The length of tubing between
the SVI II ESD and the valve shall be kept as short as possible
and free of kinks

Instrument Air Pressure 30 - 120 psi (2.07 - 8.27 bar) (207 - 827 kPa)

Dew Point

At least 18° F (-8° C) below minimum anticipated ambient tem-
perature

Particulate Matter

Filtered to 5 microns

Oil Content

Less than 1 ppm w/w

Contaminants

Free of all corrosive contaminants

«
...
71
72
73
74
75
...
»

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды