manualshive.com logo in svg

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Поделиться
Скачать
Masoneilan SVI II ESD Скачать руководство пользователя страница 69

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

69

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

3. Select mounting hole A, B, C or D for the stroke of the valve. For example, hole B is shown 

in Figure 46 on page 68 for a size 10 actuator with 1.0" stroke. Unless otherwise specified, 
the SVI II ESD mounting assumes that the actuator is in the normal upright position. The 
mounting hole in the slotted opening of the mounting bracket must be left when facing 
the actuator, with the actuator in the upright position.

4. Thread the take-off rod to the actuator stem connector. Refer to Figure 47. Ensure that the 

travel pointer located on the coupling is correctly positioned.

5. Attach the right hand threaded rod end to the SVI II ESD lever using a 1

⁄

4 - 20 x 1" cap 

screw and nut as shown. The lever hole position to be used depends upon the specific 
valve stroke. Refer to Figure 47 on page 69 and the Reciprocating Valve Linkage Selection, 
Table 6 on page 70.

6. Thread the right hand lock nut and turnbuckle onto the right hand rod end approximately 

two turns. Turnbuckle length is a function of actuator size. (Refer to Table 6 on page 70.)

7. Secure the magnet housing assembly, including the lever and right hand rod end, to the 

bracket using four M5 X 10 mm flat head screws.

8. Attach the left hand threaded rod end to the take-off rod with 1

⁄

4 - 20 UNC nut and thread 

the left hand lock nut onto the rod end.

Figure 47 Reciprocating Linkage

9. Move the valve to its closed position. For air to extend, this requires using air pressure in 

the actuator to fully stroke the actuator. For air to retract, actuators vent the actuator of 
air pressure. 

10. Thread the turnbuckle onto the left hand threaded rod end. Refer to Figure 47.

11. Adjust the turnbuckle until the hole in the SVI II ESD lever is aligned with the indicating 

hole in the bracket. Tighten both turnbuckle lock nuts. Refer to Figure 47.

12. For reciprocating valves the adjustable link turnbuckle must be parallel to the valve stem. 

To ensure linearity in positioning, verify that the hole in the lever aligns with the indicating 
hole in the bracket when the valve is in the closed position. Check that the bracket is 
mounted using the proper holes. (Refer Table 6 on page 70.).

13. Mount the SVI II ESD to the bracket and secure with four M6 socket head cap screws.

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды