Masdaf NMM Series Скачать руководство пользователя страница 5

Страница: 5 / 28

NMM Series

The warranty conditions will only be valid when all the

instructions about installation and start-up operations

of the pump unit are taken into account.

2.4. Test

All Pumps are dispatched for sale when all the

performance and pressure tests are completed. Proper

assurance of material and fault-free operation of

pumps whose performance tests are made is under the

warrantyof

MAS DAF MAKINA SANAYI A.Ş.

2.5. Pressure Limit

Pressure at the discharge flange must not exceed 10

Bar. A special order is necessary for applications with

higher pressures.

3. SAFE OPERATING CONDITIONS

This manual contains main safety instructions for the

installation, operation and maintenance. It must be

read by the personnel who are responsible for installa-

tion and operation. This manual should always be kept

near the installation location. It is important to comply

with safety precautions stated in page 1 along with the

general safety instructions as well as preventive

measures repeated in other sections of this manual.

3.1. Training of Personnel

Installation, operation and maintenance personnel

must have necessary knowledge in order to accomplish

the given job. The responsibility, adequacies and

controlling duties of such personnel must be

determined by the costumer. It has to be certain that

these personnel comprehend totally the content of the

operating manual.

If the personnel do not have enough knowledge,

required training must be given by the costumer. If

training support is needed by the costumer, it will be

provided by the manufacturer/seller.

CAUTION

Untrained personnel and unwillingness to comply with

safety instructions may be risky for both machine and

environment.

MAS DAF MAKINA SANAYI A.Ş.

is not

responsible for this kind of damages.

3.2. Hazardous Conditions That May Occur When One

does not Comply With the Safety Instructions

Incompliance with safety regulations may put the

personnel, the environment and the machine in danger

and thus may cause damages. Incompliance with safety

regulations may give rise to situations listed below.

Important operational functions of the factory may

stop.

Maintenance may get difficult.

One may get injured by electrical, mechanical or

chemical hazards.

3.3. Safety Measures for Operator

Dangerous, hot or cold components in the pump area

must be covered so that one cannot touch them.

Moving components of the pump must be covered so

that one cannot touch them. Those covers must not be

dismounted while the pump is running. Dangers that

results from electrical connections must be removed.

To get more information about this subject, you can

refer to domestic electrical instructions.

3.4. Safety Measures for Maintenance and Installation

The costumer must assure that all maintenance, check

and installment tasks are performed by qualified

personnel. Repair work must only be performed while

the machine is not running.

The pump and its auxiliary system must be cleaned

thoroughly if it contains hazardous liquids. At the end of

the repair work, all safety and protective equipment

must be re-installed.

3.5. Spare Parts Replacement

Replacement of spare parts and all modifications must

be done after contacting with the manufacturer. Spare

parts and accessories certified by the manufacturer are

important for the safe operation of the system.

Notice: MAS DAF MAKINA SANAYI A.Ş.

is not responsible

from the usage of improper spare parts.

4. TECHNICAL INFORMATION

4.1. Design

These are close coupled, single stage, single suction

with a horizontal opening and a vertical discharge

opening volute type (with horizontal shaft) pumps. They

have closed radial impellers and their casing sizes are in

accordance to DIN 24255 and EN 733 standards.

4.1.1. Locations of Flange – Flanges

Suction Flanges: In axial direction

DN50-DN150

Discharge Flanges: Radially upward DN32-DN125

Standard of Flanges:

TSE EN 1092-2

4.1.2. Connection of Pump and Motor

Motor is close coupled to the pump with a rigid coupling

using and an adapter and flange. In this way, the shafts

of the motor and pump constitute a complete unit.

Содержание NMM Series





























Результаты поиска

Содержание NMM Series

Отзывы:

Бренды по названию

Популярные бренды

Masdaf NMM Series, Руководство по эксплуатации

Результаты поиска

Содержание NMM Series

Отзывы:

Бренды по названию

Популярные бренды