background image

WIRELESS 

INTRODUCTION  

Š

 FCC Statement 

This device complies with part 15 of the FCC rules.    Operation is subject to the following two 
conditions: (1)This device may not cause harmful interference and (2) This device must 
accept any interference received, including interference that may cause undesired operation 

Notice : The changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no 
change to the antenna or the device is permitted. Any change to the antenna or the device 
could result in the device exceeding the RF exposure requirements and void user’s authority 
to operate the device. 

z

Introduction

 

Thank you for purchasing our product.    This PLL synthesized wireless microphone system 
operates in UHF band frequency with 700 selectable channels. Please read this instruction 
manual carefully before operating the system.    This manual covers the function and 
operation of the wireless microphone system. 

Š

 Safety   

¾

Do not spill liquid on the appliance and do not drop it on a hard concrete floor. 

¾

Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc.

¾

If the equipment is not going to be used for a long time, disconnect the AC adapter from 
the power outlet. Please note that if you turn the equipment off while leaving the AC 
adapter plugged in, it is not fully isolated from the power supply.

¾

Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain, 
mechanical vibrations, or shock.

¾

Take out the battery from transmitter, if the appliance has been not used for a longer period.
This will avoid the damage resulting from a defective leaking battery. 

¾

WARNING: To reduce the risk of fire or electric shock, do not use the products near water 
and do not expose them to rain or moisture. 

¾

No guarantee claims for the equipment and no liability for any resulting personal damage 
or material damage will be accepted if the equipment are used for other purpose than 
originally intended, if the equipment are not correctly connected or operated, or if the 
equipment are not repaired in an expert way. 

Š

 Environment 

¾

Do not throw used batteries into a fire or garbage bin with domestic rubbish.    Be sure to 
dispose of used batteries in accordance with local waste disposal rules. 

¾

When disposing the equipment, remove the batteries, separate the case, circuit boards, 
and cables, and dispose of all components in accordance with local waste disposal rules.

1

Содержание UF-9H

















Отзывы: