background image

 

 

SAFETY INFORMATON 

 

 

1.1 Safety Precautions 

 

Before using this equipment, study the entire owner

s manual to become familiar 

with  its operation.  Do  not  allow  untrained  or unauthorized  personnel,  especially 
children, to operate this equipment. Use only factory authorized parts for service. 

 
This  manual  contains  DANGER,  WARNING,  CAUTION  callouts 
which must be followed to reduce the possibility of personal injury, 
damage to the equipment, or improper service. 
 
This  is  the  safety  alert  symbol.  It  is  used to  alert  you  to  potential 
personal injury hazards. Obey all safety messages that follow this 
symbol to avoid possible injury or death. 
 
 
 
DANGER indicates a hazardous situation which, if not avoided, will 
result in death or serious injury. 
 
 
 
 
WARNING  indicates  a  hazardous  situation  which,  if  not  avoided, 
could result in death or serious injury. 
 
 
 
 
CAUTION  indicates  a  hazardous  situation  which,  if  not  avoided, 
could result in minor or moderate injury. 
 
 
 
 
 
 
 
 
 
 
 
 

 

!   

 

!   

DANGER 

 

!   

WARNING 

 

!   

CAUTION 

Содержание MFS 14





















Отзывы: