OPERATING
INSTRUCTIONS
Uncoil the cord and plug heater into
120 Volt, 60 Hz. alternating current.
Set Power Selector Knob to the desired
position:
1.
Off Position:
only power indicator
light is on.
2.
Humidifier Only Setting:
for steam
/ fragrance only. Note: temperature
control knob must be on high setting (5).
3.
800 watt Setting:
for upper
element, fan and steam / fragrance
operation.
4.
1500 watt Setting:
For both
elements, fan and steam / fragrance
operation.
Note: Only one quartz tube glows at
the 800 watt setting. Both tubes
glow at the 1500 watt setting.
Note: It is not neccessary to fill humidifier
to use your heater.
TEMPERATURE
CONTROL KNOB
ON / OFF
CONTROL AND
POWER
SELECTOR KNOB
Freezeguard
®
- Setting the Termperature
Control knob to Freezeguard will automatically
cause the unit to turn on before the room
temperature reaches freezing.
Power Indicator Light
- Cautions that
your unit is plugged into an electric outlet.
When light is “On,“ unit may heat up when
room temperature drops to thermostat setting
(depending on power switch setting).
Overheat Light
- When lit, Indicates unit
has overheated and has shut-off.
See instructions below.
Tip Over Switch
- Your heater is designed
to automatically shut off when tipped forward or
backward. When returned to normal upright
position heat will operate normally. This is a
safety feature to avoid the possibility of fire
should the unit be accidentally upset.
Safety Guard Latch
- This heater is
equipped with a special guard locking device.
During normal operation, the guard should be
closed and locked in position.
Safety Thermal Sensor
- This heater is
equipped with a continuous capillary sensor
that will shut the heater off when it gets
excessively hot from being covered by clothing,
etc.
See instructions below.
If this heater shuts off and the
overheat light glows:
1. Unplug heater and allow to cool.
2. Make sure the front of the heater is not
blocked, covered, or close to any other objects.
Also, do not sit, or allow a large pet to sit, too
close to the heater - this could also cause the
heater to overheat.
3. Check to see if the heater guard or reflector
is dirty. This could cause the heater to
distribute heat poorly - ultimately causing it to
overheat.
(See cleaning instructions)
4. When the heater has cooled, sensor will
reset and allow heater to operate again.
5. If you still have difficulty, call our Service
Department between 9:00 a.m. & 5:00 p.m.
EST for assistance: Toll-Free: 1-800-733-1706.
SAFETY
FEATURES
Always set the Power Selector Knob to
“Off” and disconnect the plug from the wall
outlet before adding water to the tank or
fragrance to the tray.
Humidifier
- Twist off the humidifier fill
cap and fill the tank to the FULL level.
Note: Do not pour fragrances in
humidifier tank. (see frangrance tray
instructions at right)
2. Do not fill the tank above the FULL
level. The excess water will come out from
the drain hole located on the side of the
unit. When the level of water reaches the
REFILL level, fill the humidifier tank up to
the FULL level again, making sure that the
heater is turned off, the plug is
disconnected and the unit is cool.
3. When there is any possibility that the
water in the humidifier tank will freeze,
drain the water from the tank by simply
tipping the heater to allow the water to run
out the drain hole.
Cleaning and Maintenance
- Make
sure to disconnect the plug from the wall
outlet before any servicing is started.
Always allow the heater to cool completely.
Do not pour water on or submerge any
portion of heater in water or any liquid.
Interior
- This heater is equipped with a
swing-open guard with safety lock for safe,
easy cleaning of the reflector.
To open guard:
locate the two slots at
the bottom center front of the heater. Insert
the plug end of the electrical cord into the
slots. This will release the guard. Swing
the guard up to clean. Wipe reflector clean
using a soft cloth, dampened with mild
detergent such as a window cleaner. A
dirty reflector may cause overheating and
shut off the heater.
To close the guard:
align the guard
latch with the hole in the center of the
heater. Push the guard latch firmly into the
hole until it locks securely.
Exterior
- Never use any harsh or
abrasive cleaners on the heater. Clean
exterior with a soft damp cloth and mild
detergent.
Storage
- Clean heater thoroughly &
drain water. Carefully coil cord around rear
storage brackets and place heater in
original carton.
Humidifier
- For humidifier cleaning
instructions see page 2.
CLEANING
HUMIDIFIER /
FRAGRANCE TRAY
POWER
INDICATOR
LIGHT
OVERHEAT
SIGNAL LIGHT
4
5
6
HUMIDIFIER FILL CAP
(TWIST OFF TO FILL TANK WITH WATER)
FRAGRANCE TRAY
DRAIN HOLE
WATER LEVEL WINDOW
HUMIDIFIER /
FRAGRANCE TRAY
Congratulations! You have
purchased the most advanced
electric heater available today.
This model heater features an exclusive,
replaceable heating element system
(patent pending). In the event that a
heating element in this heater should
break, burn-out or become inefficient,
you can purchase replacement elements.
To find the nearest location of a retailer
who sells Marvin
®
Replacement Heating
Elements, call our Customer Service Dept.
Toll-Free
between 9:00 a.m. and 5:00 p.m.
EST for assistance:
1-800-733-1706.
REPLACING
ELEMENTS:
Unplug the heater and allow to cool.
Open Guard
Facing the front of the heater, locate the
two slots near the bottom in the center.
(see photo in the cleaning section)
.
Using the plug on the end of the cordset,
insert the prongs into the slots. This will
release the guard latch mechanism
allowing the guard to swing up easily.
REPLACEABLE
HEATING ELEMENTS
4. Do not drain the water immediately after the
humidifier has been used because the
temperature of the water is very hot.
5. One full tank will be sufficient to generate
humidity for approximately 8 hours.
Note:
Heater will operate normally and safely
without water in tank.
Fragrance Tray
- If desired, put some
liquid potpourri or fragrance oil in the
fragrance tray. When the heater is operating,
the tray will warm releasing fragrance into your
room.
Warning:
Do not move the heater when the
tray is full. Always remove the Fill Cap/
Fragrance Tray to clean.
Starting Heater -
Turn Temperature
Control Knob to the right as far as it will
go. Leave at this setting until the room has
reached the desired temperature then turn
the control knob to the left until the heater
turns off. This is your ideal setting. The
heater will start automatically when the
room temperature drops below this setting
and will turn off once the set temperature
is reached.
Warning:
The Freezeguard
®
feature
does not insure the area to be heated will
not freeze- only that the unit will operate
before freezing temperatures are reached.
No Freezeguard protection is afforded in
the event of a power failure.
Remove Old Element
Make sure the heater is unplugged and
cool.
CAUTION: HEATING ELEMENT IS
GLASS, PLEASE HANDLE WITH CARE.
Grasp the element and push towards the
right socket. This should allow the left end
of the element to clear the left socket and
allow you to remove the element.
Install New Element
Remove the new heater element from the
card-board holder. Install one end of an
element into the right element socket.
Push the element into the socket while
guiding the other end of the element into
the left element socket.
(see photo below)
If you are replacing both elements,
repeat the above procedure for the second
element.
Close Guard
Align the guard latch with the hole in the
center of the heater. Push the guard latch
firmly into the hole until it locks securely.
7
INSTALLING REPLACEMENT
HEATING ELEMENTS
