
F U L L O V E R L AY PA N E L I N S TA L L AT I O N I N S T R U C T I O N S
7
O P E R AT I O N
4
Start Your Appliance
Your appliance will start upon initial plug-in. The LED
will flash amber upon this initial plug-in due to your
unit being powered-on at the factory to verify
performance and then powered-off. The Sentry system
senses a power outage has occurred and relays this
information to you when you initially power-on your
appliance. This is normal and pressing the
“ON/OFF” button will reset this alarm function.
If your appliance’s control has been shut-off i.e., unit
plugged in, interior lights operate, display blank,
unit must be turned on. To turn on your appliance,
push and hold for 5 seconds, the “ON/OFF” button
located on the display panel. (See figure 3) Once
products are loaded, allow at least 48 hours for the
unit to stabilize before making any adjustments to
the initial setting.
Set Your Temperature Mode
This product can display either Fahrenheit or Celsius.
To do this press the ”°F/C“ button on display panel.
Set the Controls
The available temperature range of the unit is from
33° to 47°F. The temperature set-point is initially set
in the factory at 38°F. The temperature set-point can
be lowered or raised by first pushing the “Set” button
on the display pad. A “SET” icon will be displayed.
This icon will turn off 10 second after completing
your adjustments. Pushing either the “Warmer” or
“Colder” buttons located on the inside of the unit on
the display pad will raise or lower the set
temperature by one degree F or C (depending on
your setting). As with any refrigeration product, there
is a slight temperature variance at different locations
within the cabinet.
Adjustable Temperature Control
The temperature control is fully adjustable from 33°
to 47°F. The range allows flexibility of temperature
preferences and provides the ideal storing and
serving temperatures.
Interior Light
The upper and lower interior lights make it easy to
view your food and beverages. The light will always
come on when either drawer is opened.
Warning Alarms
Your unit has been fitted with a Sentry system. This
sentry will let you know if your unit is not functioning
properly for optimum food and beverage storage.
Door Ajar Alarm
If a drawer has been left open for over 5 minutes the
alarm will sound and the LED will flash green. This
will stop as soon as the drawer is closed.
High and Low Temperature
If your unit reaches temperatures outside normal
operating temperatures for your set-point for about
one (1) hour duration, an alarm will sound and the
LED will flash red. This will warn you that your food
and beverages have seen temperatures that may not
be conducive for long term storage.
Power Failure
If your unit experiences a power failure the LED will
flash amber until the alarm is reset.
Reset Alarms
Press the “ON/OFF” button for approximately one
second. This will reset all audible and display alarms.
Sabbath Mode
Your appliance is equipped with a Sabbath mode.
By activating this mode you will be disabling all
displays, audible alarms and lights. The system will
be overridden with a random control. To activate the
Sabbath mode press and hold the “Set” button while
pressing the ”°F/C“ button 7 times within 7 seconds.
To disable the Sabbath mode repeat the process.
The Sabbath mode will deactivate after 96 hours.
figure 3
Step 3
Size the Overlay Panel
Step 4
Attach the Overlay Panel to the Door
1. Set the overlay panel on drawer front face and
align edges. Clamp panel in position and mark
pilot hole locations. See Step 3 for nominal size
and hole locations. Drill pilot holes. Remove
panel if necessary, then realign and re-clamp
overlay to drawer face.
2. Insert wood screws through clearance holes and
tighten to secure overlay panel.
3. Reinstall gasket into channel. Make sure the
corners are inserted fully.
Step 5
Reattach Drawer Front to Drawer Body
1. Align mounting holes on drawer body with
mounting holes on drawer front. Align the door
liner to the front flanges by using the erasable
marker alignment lines that were applied prior
to removing the door from the drawer in Step 2.
Reinstall phillips head screws and washers.
Snug down, but do not tighten fully; final
adjustment of drawer front will be done after
reinstalling the drawer.
Step 6
Reinstall the Drawer
1. Fully extend drawer slides and place drawer on
slides. Be sure that drawer sits evenly on both
slides.
2. Lock drawers into drawer slides. Push drawer
locks down and then back to relock the drawer
into the slide.
Step 7
Adjust Drawer Front
1. Adjust drawer front to achieve a 1/8" gap from
the top of the drawer front to the top of the
cabinet or (for bottom drawers) 1/8" from the
top of the drawer front to the bottom of the top
drawer, the drawer front should be centered
between the cabinet edges.
2. Fully tighten phillips head screws to complete
overlay panel installation.
10.06
29.06
.56
.56
7.59
14.63
15.19
29.63
19.53
figure 8