Maruyama ED2300 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 27

Maruyama ED2300 Скачать руководство пользователя страница 25

Flexible Drive Shaft Maintenance

Maintenance Interval

The Edger uses a flexible drive shaft inside the drive
shaft tube. The flexible drive shaft should be lubricated

after each 30 hours of use.

Flexible Drive Shaft Lubrication

Gearhead

Flexible Driveshatt

�

\

Drlve Shatt Tube

\

Phillips Hex Head

Screw (2)

#2 Lithium-base

Bearing Lube

1.

Loosen the two Phillips hex head screws holding
the gearcase to the drive shaft tube and carefully
remove the gearcase from the drive shaft tube.

2.

Grip the end of the flexible drive shaft and remove
it from the drive shaft tube.

3.

Lubricate the flexible drive shaft with a high qual

ity #2. lithium-base bearing lube.

4.

Reinstall the flexible drive shaft into the drive

shaft tube. Twist the flexible drive shaft as you
insert it into the to ensure that it seats into the
clutch drum.

5.

Reinstall the gearcase onto the drive shaft tube,
then tighten the two Phillips hex head screws.

Gearcase Maintenance

Maintenance Interval

The gearcase should be checked for lubrication after
each 30 hours of use.

Gearcase Lubrication

Bearing Lube

(P/N 211337)

Gearcase

Attaching Shaft

Boss Adapter

Remove the cutting attachment and the boss  adapter.
Clean any dirt. and debris from the area l:letween  the
boss adapter and the gearcase.  Remove the grease· plug
from the  side of the  gearcase..  While  rotating the
attaching shaft,  inject lithium-base·tieij.ring'lube  (PIN

211337) through the plug hole until the gearcase is full.

Reinstall the boss adapter and grease plug."

-23-

«
...
23
24
25
26
27
»

Содержание ED2300




























Отзывы:

Нет отзывов