Martin smartMAC Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 56

Martin smartMAC Скачать руководство пользователя страница 3

Safety Information

The following symbols are used to identify important safety information on the product and in this manual:

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock, lamp
explosion and falls.

Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed
below and observe all warnings in this manual and printed on the fixture. If you have questions about how to
operate the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hotline at +45
70 200 201.

P R O T E C T I O N F R O M E L E C T R I C S H O C K

• Disconnect the fixture from AC power before removing or installing any cover or part – including the lamp

and fuses – and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical codes and has both

overload and ground-fault (earth-fault) protection.

• Connect this fixture to AC power using either the supplied power cable or a listed, 3-conductor, 1.5 mm

2

(14 AWG) minimum cable that is rated minimum 8 amp, hard usage. Suitable cable types include SJT, ST,
STW, SEO, SEOW and STO.

• Before using the fixture, check that all power distribution equipment and cables are in perfect condition

and rated for the current requirements of all connected devices.

• Do not use the fixture if the power cable or power plug are in any way damaged, defective or wet, or if they

show signs of overheating.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

WARNING!

Read the safety precautions in this section before

installing, powering, operating or servicing this

product.

DANGER!
Safety hazard.
Risk of severe
injury or death.

DANGER!
Hazardous
voltage. Risk of
lethal or severe
electric shock.

WARNING!
Fire hazard.

WARNING!
Burn hazard. Hot
surface. Do not
touch.

WARNING!
Risk of eye injury.
Safety glasses
must be worn.

WARNING!
Risk of hand
injury. Safety
gloves must be
worn.

WARNING! Refer
to user manual.

«
1
2
3
4
5
...
»

Содержание smartMAC

























































Отзывы:

Нет отзывов