background image

10

Controller Operation

 

A D D R E S S   A N D   M O D E   S E T T I N G S

On the rear of the unit is a 10-way DIP-switch with the following functions:

D M X   M O D E   S E T T I N G

The Destroyer/Punisher has two DMX modes: a 1-channel mode and a multi-
channel mode that requires 5 channels for the Destroyer and 6 channels for the
Punisher

The 1-channel mode is simpler and saves channels on your controller. In this
mode, the unit becomes more aggressive the higher you set the fader. The Martin
MC-1 controller is specially designed to operate the Destroy/Punisher and other
Martin products is 1-channel mode. When using the Destroyer X250 and Punisher
X250 with the MC-1, the address (see below) must be set to DMX channel 1. 

For full control of each effect, use the multi-channel mode. The functions of each
mode are described in appendix a. 

Use DIP-switch 9 to select the DMX mode. Flip the pin ON for 1-channel 

operation of OFF for multi-channel operation. 

A D D R E S S   S E T T I N G

Use the first 8 DIP-switches to set the DMX address (the first DMX channel on
which the Destroyer/Punisher responds to the controller) to any value between 1
and 255. The address is the sum of the values for each individual DIP-switch that
is ON. 

Important! DIP-switch 10 must be flipped ON when using the Destroyer or 

Punisher with a controller. Otherwise, both the unit and the 
controller will transmit DMX signals and damage to one or 
both devices may occur.

1 Select an address for the fixture on your controller. When using the MC-1

controller, the address must be DMX channel 1.

2 Look up the DIP-switch setting for the address on page 11. 

3 Set pins 1 through 8 to the ON (1) or OFF (0) position as listed in the table. 

4 Set pin 9 to ON for 1-channel operation, or OFF for multi-channel operation. 

5 Set pin 10 to the ON position.

Switch

ON

OFF

1 - 8

DMX address (1 - 255)

9

1-channel DMX

Multi-channel DMX (5/6)

10

Slave (DMX reception)

Master (DMX transmission - 
Destroyer only)

35000035C.FM  Page 10  Wednesday, January 3, 2001  9:33 AM

Содержание Destroyer X250

















Отзывы: