Martin Audio MA1.3 Скачать руководство пользователя

Страница: 22 / 24

TECHNICAL SPECIFICATIONS

MA1.3

INPUT IMPEDANCE

20kohms (balanced) 10kohms single ended

GAIN SELECT SWITCH

37dB (I/P sens 0.775V), 32dB (I/P sens 1.27V)

CMRR@1kHz

>50dB

OUTPUT IMPEDANCE@1kHz

0.07 ohms

POWER BANDWIDTH

10Hz - 50kHz

SLEW RATE

40V/us

HUM/NOISE

<-105dB

CHANNEL SEPARATION

1kHz - 90dB
10kHz - 75dB

MAINS OPERATING VOLTAGE

120 - 270 (minimum start voltage 190) full
output power maintained 180 - 280V.
Optional (65 - 135V) operation.

PROTECTION

DC, High temperature, Turn on, VHF, Over and
under voltage, Clip limiters. Short circuit.

DISTORTION

THD 20Hz - 20kHz and 1W - 600W

4 ohms 0.08%

THD at 1kHz and 600W

4 ohms 0.03%

DIM 30 at 300W

4 ohms 0.02%

CCIF (13 and 14kHz) at 200W

4 ohms 0.02%

SMPTE (60Hz and 7kHz) at 300W

4 ohms 0.05%

POWER MATRIX

LOAD

CONFIGURATION

POWER OUTPUT

16 ohms

Stereo (2 channel)

190W

8 ohms

Stereo (2 channel)

350W

4 ohms

Stereo (2 channel)

650W

2 ohms

Stereo (2 channel)

900W*

16 ohms

Bridged mono

750W

8 ohms

Bridged mono

1400W

4 ohms

Bridged mono

1800W*

* Thermal protection may occur at high continuous power.

Power in watts (E1A 1kHz, 1% THD).

DIMENSIONS

(W) 483mm x (H) 88mm x (D) 310mm
(W) 19ins x (H) 3.5ins x (D) 12.2ins

WEIGHT

8Kg (18lbs)

SHIPPING DIMENSIONS

(W) 560mm x (H) 190mm x (D) 500mm
(W) 22.4ins x (H) 7.6ins x (D) 20ins

SHIPPING WEIGHT

10Kg (22lbs)

Martin Audio – MA1.3 Power Amplifier

NGLISH

CONTENTS

PRINT

GUIDES

Содержание MA1.3

























Результаты поиска

Содержание MA1.3

Отзывы:

Похожие инструкции для MA1.3

Бренды по названию

Популярные бренды

Martin Audio MA1.3, Руководство пользователя

Результаты поиска

Содержание MA1.3

Отзывы:

Похожие инструкции для MA1.3

Бренды по названию

Популярные бренды