manualshive.com logo in svg

Marti Electronics SRPT-30, Руководство пользователя

Поделиться
Скачать
Marti Electronics SRPT-30 Скачать руководство пользователя страница 31

8/7/2003

25

CAUTION & WARNING

NEVER INSTALL AND CONNECT THE 12-15 VOLT AND THE 15-30 VOLT SUPPLIES AT THE SAME TIME.

ALSO, NEVER CONNECT THE 15-30 VOLT SUPPLY TO THE 12-15 VOLT PINS AND NEVER CONNECT THE

12-15 VOLT SUPPLY TO THE 15-30 VOLT PINS.

DOING SO MAY DAMAGE THE INTERNAL SWITCHING SUPPLY OR EITHER OF THE EXTERNAL DC

SUPPLIES.

Connect up Antenna

Connect antenna to the ANTENNA connector on the SRPT-30/40A rear panel. Connection of various antenna

systems is covered under 

INSTALLATION

 

and

 

ANTENNAS

.

CAUTION & WARNING

THE ANTENNA CONNECTOR IS A TYPE “N” FEMALE CONNECTOR AND REQUIRES A MATING

TYPE “N” MALE CONNECTOR.

PLUGGING IN A “UHF TYPE (PL-259 OR SO-239)” INTO THE ANTENNA CONNECTOR WILL

DAMAGE AND SHORT OUT THE ANTENNA CONNECTOR. THIS COULD BURN UP THE PA

MODULE AND OTHER INTERNAL COMPONENTS.

CAUTION

DO NOT TURN ON AC LINE OR EXTERNAL DC POWER UNTIL ANTENNA HAS BEEN

PROPERLY CONNECTED TO ANTENNA CONNECTOR!

Power-Up SRPT-30/40A

If using AC line, turn on SRPT-30/40A by turning on front panel AC LINE switch. If using 12-15 Volt or 15-30

Volt external DC supply, turn on SRPT-30/40A by turning on external DC supply. Refer to the 

External DC Supply

Operation

 procedure above for proper installation and operation.

The SRPT-30/40A will begin a power-up routine. The front panel meter will illuminate immediately. After about

three seconds the AFC LOCK LED will begin flashing green indicating that the synthesizer is searching for the last
frequency it was last locked on to.

If the TRANSMIT/STANDBY switch is in the TRANSMIT position, the TRANSMIT LED will flash red in unison

with the green flashing AFC LOCK LED. Once the synthesizer has found and locked onto the frequency, the AFC
LOCK LED will immediately stay on solid green and the TRANSMIT LED will continue to flash red for three
additional seconds. After the three seconds, the SYNTHESIZER will be ready, will enable the power amplifier to
transmit RF power, and the TRANSMIT LED will stay on solid red.

Содержание SRPT-30


































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды