background image

MAINTENANCE

 

 

If further maintenance is required beyond the scope of this direction sheet and the tool fails to function 
properly, contact the factory or return it to the factory for service.  
Contact our Tool Repair Center at 317-704-8874 or visit our web site at  www.afs-idg.com for further 
information. 

 

LIMITED TOOL WARRANTY

 

 

Alcoa Fastening Systems (Marson) warrants that this tool, will be free from defects in material and 
workmanship under normal service,  for ninety (90) days from the date of purchase. This warranty 
applies to the purchaser of the tool for original use only. All other warranties, whether expressed or 
implied, including any warranties of merchantability or fitness for purpose are hereby excluded. 

Should this tool fail during this ninety (90) day period, and no unauthorized repairs have been made, 
return the tool freight prepaid to the factory for free of charge replacement of any part or parts found by 
Alcoa Fastening System (Marson) to be defective due to faulty material or workmanship. This represents 
the sole obligation of Alcoa Fastening Systems (Marson) under this warranty. In no event shall Alcoa 
Fastening Systems  (Marson) be liable for any consequential or special damages arising from the 
purchase or use of this tool. You may have other rights which vary from state to state. 

 

 

 

 

pg.  9 

Содержание SST-1










Отзывы: