8
Compatible Input Formats
Format
Composite
S-Video
YPbPr
SDI
VGA
DVI-D
NTSC
●
●
PAL
●
●
525i
●
●
●
625i
●
●
●
486p / 59.94
●
576p / 50
●
●
1035i / 60
●
●
1035i / 59.94
●
●
1080i / 60
●
●
●
●
1080i / 59.95
●
●
●
●
1080i / 50
●
●
●
●
1080psF / 24
●
●
●
●
1080psF / 23.98
●
●
●
●
1080p / 30
1080p / 29.97
1080p / 25
720p / 60
●
●
●
●
720p / 59.94
●
●
●
●
720p / 50
●
●
●
●
720p / 30
720p / 29.97
720p / 25
640 x 480 @ 60Hz
●
●
640 x 480 @ 75Hz
●
●
640 x 480 @ 85Hz
●
●
800 x 600 @ 60Hz
●
●
800 x 600 @ 75Hz
●
●
800 x 600 @ 85Hz
●
●
1024 x 768 @ 60Hz
●
●
1024 x 768 @ 75Hz
●
●
1024 x 768 @ 85Hz
●
●
1280 x 1024 @ 60Hz
13
On-Screen Menu (continued)
VIDEO CONFIGURATION SUBMENU (continued)
■
Monochrome Mode
Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale
picture.
■
Blue-Only Mode
Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching
off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following
procedure:
1.
Allow the monitor to warm up for at least 5-10 minutes.
2.
Display SMPTE split-field color bars on the monitor using the internal generator or an external source.
3.
Enable
Monochrome mode
.
4.
Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the
Brightness
knob until there is
no visible difference between the super black and black bars, but the gray bar is still visible.
5.
Adjust the
Contrast
knob until an even grayscale appears along the top bars.
6.
Disable
Monochrome mode
.
7.
Enable
Blue-Only mode
and adjust the
Color
knob so that the outermost bars (white and blue) appear to match in brightness.
8.
Composite/S-Video NTSC only: Adjust the
Tint
knob until the third bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.
9.
Disable
Blue-Only mode
.
■
Pixel-to-Pixel
™
Mode
Use this setting to enable Pixel-to-Pixel
™
mode.
This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and
aspect ratio, with a one-to-one mapping:
•
For incoming formats smaller than the native resolution of the LCD panel (800 x 600), the image will be displayed
in the center of the screen using only the necessary LCD pixels. For example, NTSC or PAL images will occupy
exactly 720 x 486 or 720 x 576 pixels respectively. The surrounding pixels will be black.
•
For incoming formats exceeding 800 x 600 pixels, only the center 800 x 600 of the incoming image will displayed
occupying the whole screen, with the remainder of the picture cropped. For example, 1080i formats will both be
cropped to 800 x 600 and displayed full-screen.
Note: Pixel-to-Pixel
™
mode will utilize the entire screen (800 x 600) regardless of the aspect ratio setting. Pixel-to-
Pixel
™
mode is not available when using the VGA or DVI inputs.
