Owner’s Manual -
Plastic Wall Fan
3
3
2
1
0
INSTALLATION INSTRUCTIONS
Name of components
Pole
Motor
Motor shaft
Rear grill
Base
Bolt
Lock nut of grill
Screw the lock nut of
grill clockwise,
and in the meantime,
fix the rear grill.
Lock nut of blade
anticlockwise,
and then install the
front fan cover.
Blade
Pull the blade to rotate after installing,
so as to ensure that the blade can be
normally rotated.
Front grill
Base Installation
Align the column with the
groove on the base and
fix them together using a
right-angle bolt.
Considerate Hint:
Remove parts from the component
before performing installation.
INSTRUCTIONS FOR USE
Align Catch of the Front Guard
with the illustrated position of
the Rear Guard.
Press guards with both hands.
Front and Rear Guard Installation
Turn counterclockwise and loosen for
performing height adjustment.
Height Adjustment
Speed control knob
Height Adjustment Key
Swing Pull-knob
Push-down to swing
Pull-up for static
Horizontal Swing
3
Pa!
1
2
Screw
Lorem ipsum
Clip
Fig.1
Fig.2
Fig.3
Front grill
Blade
Spinner
Plastic nut
Rear grill
Motor shaft
Motor
Note: All the pictures in this manual are for explanation purpose only. Any discrepancy between
the real object and the illustration in the drawing shall be subject to the real subject.
Clip
Fig.1
Fig.2
Fig.3
Front grill
Blade
Spinner
Plastic nut
Rear grill
Motor shaft
Motor
Note: All the pictures in this manual are for explanation purpose only. Any discrepancy between
the real object and the illustration in the drawing shall be subject to the real subject.
OPERATION INSTRUCTIONS
The fan should be installed on a solid vertical surface.
Caution : To prevent the fan from falling off, do not install it on walls less then 4 inches
thick or made of materials that are easily damaged.
Installing the mounting bracket
Attach the supplied mounting bracket firmly to the wall using the three screws included.
NOTE:
The bracket should be positioned at least 14 inches from the ceiling and at least
12 inches from adjoining wall.
Installing the stand
Mount the stand on the bracket by inserting the bracket catch into the slot on the stand.
Fix the stand onto the bracket with a retaining nut.
NOTE:
If the retaining nut does not pass through the holes, push the stand downwards
until it is fully mounted on the bracket.
SPEED ADJUSTMENT
Adjust to the desired speed by pulling the switch cord (A).
0---Off 1---Low 2---Medium 3---High
OSCILLATION CONTROL
Pull switch cord (B) to start and stop oscillation.
TO ADJUST THE WIND DIRECTION
Push the guard lightly to the desired up or down direction.
USER SERVICING INSTRUCTIONS
a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pull
-
ing on cord.
b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards
blades.
c) Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal),
then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it
at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse
out entirely.
d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard prod
-
uct if the attachment plug is damaged.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause
accident.
2. When you feel it hard to be operated, please make sure you have got the right way.
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge, thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.
